Field fix / guideProcedureVendor-agnosticPower Plantindustrial-automation

Boiler Drum Level — 3-Element Control — Engineering Guide

Shared by TSIMEREZIVO Team · 4 Oct 2026 · 43 views

# Boiler Drum Level — 3-Element Control End-to-end cascade control example — steam drum feedwater regulation using drum level (Element 1), steam flow feedforward (Element 2), and feedwater flow cascade (Element 3). Includes shrink-swell compensation, ISA-18.2 alarms and IEC 61511 SIS interface. 45 min read 9 sections Hardware: Siemens S7-400H / 710 mm DP cell IEC 61511 SIL-2 trip required Power generation / chemical plant > **Prerequisites** — Before working through this example, ensure you have completed: - TSIMEREZIVO Quick-Start path (Sections 1–4 of the platform documentation) - Single-loop PID control fundamentals (see *PID Control* article) - VFD Motor Control example — tag configuration basics - Your plant risk assessment confirms a SIL-2 rated SIS is installed for drum high-high level trip ## 1. Process Overview — Why 3 Elements? A boiler steam drum must maintain water level within a tight band (typically ±50 mm of Normal Water Level). Too low → uncovered tubes overheat and rupture. Too high → wet steam carries water to turbine blades (water hammer — catastrophic). ### Why a Single-Element Controller Fails The Shrink-Swell Phenomenon When steam demand suddenly increases, drum pressure drops momentarily. The steam bubbles in the water column **expand**, causing the drum level to **rise** — even though more feedwater is urgently needed. A single-element (level-only) controller sees a *high* level and closes the feedwater valve. The wrong action. Minutes later the bubbles collapse, level crashes below LL, and the SIS trips the boiler. The 3-Element Solution Element 2 (steam flow) acts as a **feedforward** signal, immediately opening the feedwater valve as demand rises — before level is affected. Element 3 (feedwater flow) provides an inner cascade loop that makes the valve follow the setpoint quickly and accurately, rejecting supply pressure disturbances. Element 1 (drum level) corrects any remaining steady-state offset. *[Diagram: 3-element feedwater control: LT-201 + FT-202 feedforward + FT-201 cascade — view in the TSIMEREZIVO docs]* ## 2. Control Strategy — ISA-51.1 Block Diagram *[Diagram: Master PID (LC-201) → Feedforward Σ → Slave PID (FC-201) → FCV-201 — view in the TSIMEREZIVO docs]* | num | label | desc | |---|---|---| | 1 | Drum Level (LC-201) | Master PID. Compares drum level to setpoint (NWL = 0 mm). Its output is the feedwater flow setpoint for the slave. Integral action corrects offset. Slow — Ti ≈ 120 s. | | 2 | Steam Flow (FT-202) | Feedforward element. Instantly compensates for steam demand changes. Adds directly to the slave setpoint, bypassing the master. Eliminates the swell/shrink response. Gain K₂ ≈ 1.0. | | 3 | Feedwater Flow (FC-201) | Slave PID. Controls FCV-201 to deliver the demanded feedwater flow. Fast — Ti ≈ 30 s. Rejects supply pressure disturbances before they affect drum level. | ## 3. Tag Configuration All instruments on the P&ID map to TSIMEREZIVO tags. The drum level control loop has 14 tags across analogue I/O, digital I/O and internal calculated values. > **ISA-18.2 Alarm Rationalisation** — Every alarm must have a unique cause, a consequence, and a required operator action within the time available (ISA-18.2 §5.5). TSIMEREZIVO alarm configuration enforces these three fields as mandatory before an alarm can be activated. Flood protection: set a deadband of 5 mm on all level alarms to prevent chattering at the setpoint boundary. ## 7. Simulation Commissioning ### Step 1 — Load the 3-Element Template In TSIMEREZIVO → Simulation, select ** Industrial Templates → Boiler Drum Level (3-element)**. The template pre-configures a first-order-plus-dead-time drum model with: - Drum volume: 15 m³ equivalent - Steady-state: 100 t/h steam = 100 t/h feedwater - Swell time constant: 8 seconds (realistic for 10 bar drum) ### Step 2 — Verify Steady-State With both PID controllers in Auto, observe all trends for 10 minutes. Drum level should hold at 0 ± 15 mm with natural drum noise. Flow should match: ` FT201:PV ≈ FT202:PV ≈ 100 t/h`. ### Step 3 — Test Steam Load Step Simulate a sudden steam demand increase: force ` FT202:PV` from 100 → 130 t/h (step). Observe: - Drum level initially *rises* 20–30 mm (swell) — expected, not a fault - Feedforward immediately increases FCV-201 opening - Level returns to NWL within 90 seconds - Feedwater flow stabilises at 130 t/h ### Step 4 — Test LAHH Alarm — SIS Interface Force `LT201:PV = +205 mm`. Verify: LAHH-201 alarm fires in TSIMEREZIVO alarm list with P1 priority, red banner. The SIS trip output (external hardware) would activate. In simulation, TSIMEREZIVO shows the `BOILER_TRIP_SIS` tag set TRUE. ### Step 5 — Test FCV-201 Failure Force `FCV201:OP = 0` (valve fails closed). Observe: - FT201:PV drops to 0 t/h → FAL-201 alarm fires within 30 s - Drum level begins to fall at ≈ 10 mm/min (full steam load) - LAL-201 fires at −150 mm ≈ 15 minutes later - LALL-201 (SIS trip) fires at −200 mm ≈ 20 minutes later This validates the Time Available to Act in the alarm rationalisation above. ## 8. Debug — Level Oscillation Troubleshooting | symptom | cause | fix | |---|---|---| | Drum level oscillates with period ≈ 5–15 min | Master PID (LC-201) Kp too high or Ti too short — controller fighting integrating process | Reduce LC-201 Kp by 30%. Increase Ti to 180s. Observe 15 min. Repeat until stable. | | Feedwater flow oscillates ≈ 10–30 s period | Slave PID (FC-201) tuned too tight. Also check for valve hunting (positioner gain). | Reduce FC-201 Kp by 20%. Check FCV-201 positioner deadband — set to 0.5% if adjustable. | | Level swell on steam load change does not recover | Feedforward gain K₂ too low — steam flow not fully compensated. | Increase K_FF from 1.0 to 1.1–1.15. Test with 10 t/h step. Tune in 0.05 increments. | | FT-201 or FT-202 reads zero or erratic | Orifice plate DP cell impulse line blocked, or condensate pot needs draining. | Check TSIMEREZIVO raw counts (AI module channel). If 4mA = 0 → open loop. Inspect field wiring. | ## 9. Safety Integrity — IEC 61511 Interface > **Safety Instrumented Functions — SIF-201** — This example includes a SIL-2 rated SIS function. The information below is for awareness only. All SIS modification must be performed by a competent Functional Safety Engineer (TÜV FS Eng or equivalent) with a full SIL verification after any change. ### SIF-201 — Steam Drum Protection Trip Initiators - • LT-201A LAHH (>+200 mm) — 2oo3 voting - • LT-201B LAHH (>+200 mm) — 2oo3 voting - • LT-201C LAHH (>+200 mm) — 2oo3 voting - • LT-201A LALL (<−200 mm) — 2oo3 voting Trip Actions - • Fuel gas shut-off valve XV-101 → CLOSE - • FCV-201 → OPEN (fail-open on loss of signal) - • Steam isolation XV-102 → CLOSE - • DCS alarm: BOILER TRIP, priority P0 ## Next Steps | href | label | desc | |---|---|---| | /dashboard/docs/vfd-motor-control | VFD Motor Control | Simpler single loop — start here if new | | /dashboard/docs/fat-procedure | FAT Procedure Guide | Full IEC 62382 checklist for this loop | | /dashboard/docs/alarm-investigation | Alarm Investigation | ISA-18.2 alarm flood analysis & ranking |

More like this

Rate, comment, and get full access

Members can download files, rate contributions, and discuss fixes with the engineers who posted them — free.

Join the library