Field fix / guideDesign DocumentVendor-agnostic (IEC 61131-3)Power Plantindustrial-automation

Main Condenser Pressure Control — Control Design

Shared by TSIMEREZIVO Team · 4 Oct 2026 · 45 views

# TSIMEREZIVO Template: Main Condenser Pressure Control **Category:** Power Plant | **Industry:** Thermal Power Generation | **Language:** Ladder / Structured Text --- ## 📋 Overview ### Purpose Maintain the main condenser absolute pressure at 0.08 bar (80 mbar) to maximize turbine expansion and power output. The condenser converts exhaust steam from the turbine back to liquid water through cooling. Lower absolute pressure = greater enthalpy drop = more power extracted from the same steam rate. ### Typical Application - **Nominal Capacity:** 100–300 MWe coal/natural gas steam plant - **Steam Pressure:** 175 bar at throttle - **Steam Temperature:** 540°C - **Condenser Design Pressure:** 0.08–0.10 bar absolute - **Cooling Method:** Once-through river water OR recirculating cooling tower - **Tube Material:** Admiralty brass or titanium (seawater-resistant) ### Standards & References - **ASME PTC 12.2** — Steam Surface Condenser Performance - **IEEE 1010** — Standard for Instruments and Apparatus for Use in High-Voltage Power Apparatus - **EPRI** — Condenser Fouling and Erosion Guidelines ### Why This Matters Every 0.01 bar rise in condenser pressure (from 0.08 → 0.09 bar) reduces turbine work by 0.8–1.2%. On a 200 MWe plant, this is 1.6–2.4 MWe of lost output = $10,000–$15,000/day in lost revenue. Operators obsess over maintaining vacuum because it directly translates to paycheck margin. --- ## 🎯 Control Philosophy ### Key Equations **Absolute Pressure Relationship:** ``` P_absolute [bar] = P_gauge [bar] + 1.0 [atmospheric] Condenser setpoint: 0.08 bar absolute = -0.92 bar gauge ``` **Cooling Load (First Law):** ``` Q_cooling [MW] = ṁ_steam [kg/s] × (h_exhaust − h_condensate) = ṁ_steam [kg/s] × 2,300 [kJ/kg] typical Example: 200 kg/s exhaust × 2,300 = 460 MW of heat rejection ``` **Cooling Water Delta-T (Clausius Rankine):** ``` ΔT_water [°C] = Q / (ṁ_water [kg/s] × c_p [kJ/kg·°C]) = 460,000 / (10,000 kg/s × 4.18) = 11°C typical ``` **Vacuum Pump Drawdown (If Air-Cooled or Hogging Turbo):** ``` % Vacuum = (P_atm − P_condenser) / P_atm × 100% = (1.0 − 0.08) / 1.0 × 100% = 92% vacuum ``` ### The Physics of Condenser Pressure The condenser is *not* actively pumped to low pressure—it naturally reaches equilibrium between: 1. **Cooling water heat removal** (pushes pressure DOWN) 2. **Air leakage into condenser** (pushes pressure UP) 3. **Circulating pump work** (small effect if water-cooled condenser) **If cooling water decreases** (fouled tubes, flow blocked): - Heat transfer coefficient ↓ → ΔT rises → Pressure cannot drop → Condenser back-pressure increases - Turbine sees higher exhaust pressure → less expansion → less power **If air leaks in** (condenser hot well seals worn): - Absolute pressure rises directly (now 0.09, 0.10, 0.12 bar) - Oxygen reacts with steel internals → iron oxide sludge → further fouling ### Control Strategy: Two-Loop Architecture **LOOP 1: Cooling Water Flow Control** (Primary) ``` Condenser Pressure ↓ [PID] (Proportional: Kp = 0.18, Integral: Ki = 0.012) ↓ Command Signal ↓ Cooling Water Valve Modulation ↓ Higher flow → Lower tube outlet temp → Lower bulk temp → Lower pressure ⬇ ``` **LOOP 2: Vacuum Pump (Standby/Startup)** ``` [Only during startup or extreme fouling] Condenser Pressure > 0.12 bar ↓ Trip Alarm → Operator starts hogging turbo (air extraction pump) ↓ Pump removes air/vapor → Pressure drops toward 0.08 ↓ Once stabilized → Pump deactivates ``` ### Setpoint Philosophy - **Normal Operation:** 0.08 bar absolute (setpoint is FIXED—do not chase load) - **Fouling Indication:** Cannot maintain 0.08 under rated load → Condenser needs cleaning - **Tube Plugging Check:** Compare pressure today vs. baseline from 6 months ago - Rise of 0.01 bar/year = typical light fouling - Rise of 0.05 bar/year = urgent cleaning needed --- ## 🏗️ Control Logic ### Pseudocode: Condenser Pressure PID with Air-In Detection ```pascal PROGRAM CondensorPressureControl; { ========== DECLARATIONS ========== } VAR -- INPUT SENSORS cond_pressure_actual : REAL; { 0-0.5 bar absolute, 4-20 mA transmitter } cooling_water_temp_in : REAL; { 0-50°C, RTD input } cooling_water_temp_out : REAL; { 0-50°C, RTD input } cooling_water_flow : REAL; { 0-100 %, pump tachometer } cond_cooling_valve_fdbk : REAL; { 0-100 %, proportional valve position transmitter } circulating_pump_run : BOOL; { Circulating pump running signal } turbine_load : REAL; { 0-100 %, main steam flow or electrical load } -- CONTROL SETPOINTS cond_pressure_sp : REAL := 0.08; { Fixed setpoint } cond_alarm_high : REAL := 0.12; { High pressure warning } cond_trip_high : REAL := 0.15; { High pressure alarm → reduce load } cooling_water_dT_min : REAL := 8.0; { Minimum approach: indicates fouling } -- CONTROL LOOP STATE pressure_error : REAL; pid_integral_term : REAL := 0.0; pid_derivative_term : REAL := 0.0; pressure_prev : REAL := 0.08; valve_command_raw : REAL; valve_command_limited : REAL; -- PID TUNING PARAMETERS kp_cond : REAL := 0.18; { Proportional gain } ki_cond : REAL := 0.012; { Integral gain: slow (heavy thermal mass) } kd_cond : REAL := 0.001; { Derivative: minimal (reduces oscillation) } integral_limit_hi : REAL := 0.30; { Max +int output } integral_limit_lo : REAL := -0.15; { Min -int output } scan_time : REAL := 2.0; { 2-second scan } -- FOULING DETECTION cooling_water_dT : REAL; fouling_indicator : REAL; { Increases over time if tubes foul } fouling_alarm_active : BOOL; -- AIR-IN DETECTION (CRITICAL) cond_pressure_stable : BOOL; pressure_change_rate : REAL; { bar/min } air_ingress_detected : BOOL; -- OUTPUT COMMANDS cooling_valve_command : REAL; { 0-100 % signal to proportional valve } BEGIN { ========== SENSOR ACQUISITION ========== } -- Read absolute pressure (0-0.5 bar range, 4-20 mA) -- If reading jumps rapidly → possible sensor fault { ========== ERROR CALCULATION ========== } pressure_error := cond_pressure_sp - cond_pressure_actual; { ========== PID CONTROL LOOP ========== } -- Proportional term: immediate response to pressure deviation pid_proportional_term := kp_cond * pressure_error; -- Integral term: accumulated error (slow correction for fouling trends) pid_integral_term := pid_integral_term + (ki_cond * pressure_error * scan_time); -- Anti-windup: limit integral term IF pid_integral_term > integral_limit_hi THEN pid_integral_term := integral_limit_hi; ELSIF pid_integral_term < integral_limit_lo THEN pid_integral_term := integral_limit_lo; END_IF; -- Derivative term: rate of change (reduce overshoot) pressure_change_rate := (cond_pressure_actual - pressure_prev) / scan_time; pid_derivative_term := kd_cond * pressure_change_rate; -- Combined command valve_command_raw := pid_proportional_term + pid_integral_term + pid_derivative_term; { ========== OUTPUT LIMITING ========== } -- Map command to valve position: -0.5 to +0.5 raw → 0 to 100 % valve -- Negative error (pressure too HIGH) → OPEN valve (more cooling) -- Positive error (pressure too LOW) → CLOSE valve (less cooling) valve_command_limited := 50.0 - (valve_command_raw * 100.0); { Center at 50% } IF valve_command_limited < 0.0 THEN valve_command_limited := 0.0; { Minimum = all cooling OFF } ELSIF valve_command_limited > 100.0 THEN valve_command_limited := 100.0; { Maximum = all cooling ON } END_IF; cooling_valve_command := valve_command_limited; { ========== FOULING DETECTION ========== } -- Calculate cooling water approach (Delta-T) cooling_water_dT := cooling_water_temp_out - cooling_water_temp_in; -- Fouling increases ΔT for same load (worse heat transfer) -- As ΔT decreases for same load → cooling improving OR fouling increasing IF turbine_load > 80.0 AND cooling_water_dT < cooling_water_dT_min THEN fouling_indicator := fouling_indicator + 0.1; { Accumulate fouling score } IF fouling_indicator > 5.0 THEN fouling_alarm_active := TRUE; { Log: "Condenser fouling detected - schedule cleaning" } END_IF; ELSE fouling_indicator := MAX(0.0, fouling_indicator - 0.05); { Decay if conditions improve } END_IF; { ========== AIR-IN DETECTION (CRITICAL) ========== } -- Air leakage manifests as inability to hold vacuum at low loads -- Or sudden pressure rise despite valve fully open pressure_change_rate := (cond_pressure_actual - pressure_prev) / scan_time; -- During normal operation at steady load, pressure oscillates ±0.005 bar -- If pressure drift exceeds 0.01 bar/min → air-in likely IF ABS(pressure_change_rate) > 0.0167 THEN { 0.01 bar/min } air_ingress_detected := TRUE; { ALARM: Air ingress in condenser - check hot well seals immediately } ELSE air_ingress_detected := FALSE; END_IF; { ========== ALARMS & INTERLOCKS ========== } IF cond_pressure_actual > cond_alarm_high THEN { WARN: "Condenser pressure high - {value} bar" } END_IF; IF cond_pressure_actual > cond_trip_high THEN { CRITICAL ALARM: Reduce turbine load immediately } { Operator should: Open feed valve more OR close turbine inlet valve } END_IF; IF cooling_valve_command >= 99.0 AND cond_pressure_actual > 0.10 THEN { ALARM: "Cooling valve saturated but pressure still high - fouling?" } END_IF; IF fouling_alarm_active THEN { ALARM: "Condenser fouling detected - schedule cleaning during next maintenance window" } END_IF; IF air_ingress_detected THEN { CRITICAL ALARM: "Possible air ingress in condenser - inspect hot well seals and check for tube leaks" } END_IF; { ========== UPDATE STATE FOR NEXT CYCLE ========== } pressure_prev := cond_pressure_actual; { ========== SEND COMMAND TO VALVE ========== } -- Output: cooling_valve_command (0-100 %) -- Proportional control valve responds with ~3-5 second lag END_PROGRAM; ``` ### Commissioning-Phase Flowchart **Startup Procedure (Cold Condenser)** ``` 1. Circulating pump energized → cooling water flows 2. Monitor time to reach 0.08 bar - Typical: 15–30 minutes (filling condenser with circulating water) - If >60 min: check for air leaks, pump cavitation 3. Once stable at 0.08, engage turbine 4. Ramp turbine load slowly (10%/min max) 5. Monitor pressure—should remain stable ±0.01 bar 6. At rated load: note baseline pressure & valve position - Baseline for future fouling comparison ``` --- ## 🏷️ Tag List ### Analog Inputs (Sensors) | Tag Name | Type | Range | Units | Description | |----------|------|-------|-------|-------------| | `COND_PRESSURE_ACTUAL` | AI | 0–0.5 | bar abs | Main condenser absolute pressure (4-20 mA) | | `COND_PRESSURE_CALC_kPa` | REAL | 0–50 | kPa | Calculated in kPa for trending | | `COOLING_WATER_TEMP_IN` | AI | 0–50 | °C | Inlet cooling water temperature (RTD) | | `COOLING_WATER_TEMP_OUT` | AI | 0–50 | °C | Outlet cooling water temperature (RTD) | | `COOLING_WATER_FTEMP_CALC` | REAL | — | °C | Delta-T: `OUT - IN` | | `COOLING_WATER_FLOW` | AI | 0–100 | % | Cooling pump/motor tachometer feedback | | `COND_COOLING_VALVE_FDBK` | AI | 0–100 | % | Proportional valve actual position (4-20 mA feedback) | | `TURBINE_LOAD_ACTUAL` | AI | 0–100 | % | Main steam flow OR electrical megawatts | | `TURBINE_EXHAUST_TEMP` | AI | 0–100 | °C | Turbine exhaust temperature (rough estimate) | ### Analog Outputs (Control Signals) | Tag Name | Type | Range | Units | Description | |----------|------|-------|-------|-------------| | `COND_PRESSURE_SP` | REAL | 0.06–0.10 | bar | Setpoint (fixed at 0.08 nominal) | | `COND_PRESSURE_ERROR` | REAL | −0.05 to +0.05 | bar | Error = SP − Actual | | `COOLING_VALVE_COMMAND` | AO | 0–100 | % | 4-20 mA output to proportional valve | | `COOLING_VALVE_PID_P` | REAL | — | — | Proportional term (debugging) | | `COOLING_VALVE_PID_I` | REAL | — | — | Integral term (debugging) | | `COOLING_VALVE_PID_D` | REAL | — | — | Derivative term (debugging) | ### Discrete Signals (Alarms/Status) | Tag Name | Type | Logic | Description | |----------|------|-------|-------------| | `CIRCULATING_PUMP_RUN` | DI | High = ON | Cooling pump status feedback | | `COND_PRESSURE_HI_WARN` | DO | Latched | Alarm if pressure > 0.12 bar (warning) | | `COND_PRESSURE_TRIP` | DO | Latched | Alarm if pressure > 0.15 bar (reduce load) | | `COND_FOULING_ALARM` | DO | Latched | Fouling detection active | | `AIR_INGRESS_ALARM` | DO | Latched | Possible air leak into hot well | | `COOLING_VALVE_STUCK_ALARM` | DO | Auto-check | Valve command ≠ feedback >10 sec | | `PRESSURE_SENSOR_FAULT` | DO | Latched | Sudden jump or no change >5 min | --- ## 🚨 Alarm & Trip Matrix | Condition | Threshold | Severity | Action | Recovery | |-----------|-----------|----------|--------|----------| | **Pressure High (Warning)** | > 0.12 bar | ⚠️ WARNING | Alert operator; monitor trend | Auto-clear if drops <0.10 | | **Pressure High (Trip)** | > 0.15 bar | 🔴 CRITICAL | Reduce turbine load 10% every 1 min | Stabilize at <0.12 bar | | **Pressure Not Changing** | Δ < 0.005 bar/5 min | ⚠️ WARNING | Check sensor; suspect calibration drift | Verify with secondary pressure gauge | | **Pressure Rising Rapidly** | > 0.01 bar/min | 🔴 CRITICAL | **AIR INGRESS!** Shut down turbine immediately; inspect hot well seals & condenser tubes | Visual inspection + tracer dye leak test | | **Cooling Valve Stuck** | Command ≠ Feedback >10 s | ⚠️ WARNING | Valve not responding to PID command; manual override | Manual valve intervention | | **Cooler ΔT Low** | ΔT < 8°C @ full load | ⚠️ WARNING | Fouling detected; schedule cleaning | Mechanical cleaning (plug tubes) | | **Cooler ΔT = 0** | ΔT < 3°C | 🔴 CRITICAL | Cooling water blockage or pump failure; no heat removal | Restart pump; clear strainers | | **Pressure Too Low** | < 0.05 bar | ⚠️ WARNING | Over-cooling or air-in paradox; check sensors | Verify with mercury barometer | --- ## 📺 HMI Layout ### Main Condenser Vacuum Status Graphic ``` ┌─────────────────────────────────────────────┐ │ MAIN CONDENSER PRESSURE MONITOR │ ├─────────────────────────────────────────────┤ │ │ │ Pressure: 0.082 bar ↑ [SP: 0.080 bar] │ │ Trend: ▁▂▂▂▂▃▃▃▃▄ ↘ (dropping slowly) │ │ │ │ ┌─── CONDENSER COOLING PATH ──────┐ │ │ │ │ │ │ │ In: 22.5°C Pump: 95% │ │ │ │ Out: 31.2°C Valve: 62% │ │ │ │ ΔT: 8.7°C ✓ │ │ │ │ │ │ │ └─────────────────────────────────┘ │ │ │ │ ╔════ LOAD ════╗ ╔════ VACUUM ════╗ │ │ ║ Turbine ║ ║ Condenser ║ │ │ ║ Load: 75% ║ ║ Pressure ▓▓ ║ │ │ ║ ║ ║ ████░░░░░░░░ ║ │ │ ║ Steam: 185 ║ ║ 0.08 bar ║ │ │ ║ kg/s ║ ║ STABLE ║ │ │ ╚══════════════╝ ╚════════════════╝ │ │ │ │ [ Baseline 6 mo. ago: 0.078 bar ] │ │ [ Annual fouling trend: +0.005 bar ] │ │ Status: ✓ Clean — Next cleaning: TBD │ │ │ │ ⚠️ [NONE] 🔴 [NONE] ℹ️ Steady state │ │ │ └─────────────────────────────────────────────┘ ``` ### Trend Graph (24-Hour History) ``` Pressure [bar] 0.12 ────────────────────────────────────── 0.10 ─────────╱╲ ╱╲ 0.08 ───────╱ ╲──────────╱ ╲─────────── ← Setpoint 0.06 ──────╱────╲──────╱──────╲────────── 0.04 ───────────────────────────────────── └──00:00──06:00──12:00──18:00──00:00── Peaks: Load ramps (turbine goes to full load) Valleys: Low-load periods (night time) / cooler inlet water ``` ### Quick-Reference Control Panels **Panel A: Operator Control** ``` Manual/Auto Mode: ● Auto ○ Manual Cooling Valve: [████████░░] 62% Valve Demand: [█████░░░░░] 51% Lock Valve at: [████░░░░░░] ``` **Panel B: Diagnostics** ``` Sensor Health: ✓ All OK Recent Faults: [Show History ▼] Air Ingress Risk: ✓ LOW (stable <±0.005 bar/min) Fouling Index: ████░░░░░░ 2.3/10 Last Cleaning: 6 months ago ``` --- ## 🔧 Configuration Parameters ### PID Tuning ```json { "cond_pressure_control": { "description": "Main Condenser Absolute Pressure PID", "setpoint_bar": 0.08, "scan_time_sec": 2.0, "pid_tuning": { "proportional_gain_kp": 0.18, "integral_gain_ki": 0.012, "derivative_gain_kd": 0.001, "integral_limit_hi": 0.30, "integral_limit_lo": -0.15, "derivative_filter_sec": 5.0 }, "valve_limits": { "min_percent": 0.0, "max_percent": 100.0, "rate_limit_percent_per_sec": 2.0, "damp_oscillations": true } }, "pressure_alarms": { "high_warning_bar": 0.12, "high_trip_bar": 0.15, "low_warning_bar": 0.05, "low_trip_bar": 0.03, "rate_of_change_limit_bar_per_min": 0.0167 }, "cooling_water_monitoring": { "delta_t_normal_min_celsius": 8.0, "delta_t_fouling_threshold_celsius": 6.0, "fouling_accumulation_rate_per_hour": 0.1, "fouling_alarm_threshold": 5.0 }, "air_ingress_detection": { "rate_of_change_threshold_bar_per_min": 0.0167, "observation_window_minutes": 5.0, "alarm_auto_reset": false }, "commissioning": { "startup_stabilization_minutes": 30, "pressure_tolerance_at_baseline_bar": 0.01, "valve_response_expected_seconds": 3.0, "temperature_ramp_celsius_per_minute": 2.0 } } ``` --- ## 📝 Implementation Checklist ### Pre-Commissioning (Desk-Top Design Review, 1 day) - [ ] PID gains calculated via Ziegler-Nichols testbed (if available) or loaded from similar plant - [ ] Pressure transmitter range verified: 0–0.5 bar absolute (NOT gauge) - [ ] RTD temperature inputs scaled correctly: 0–50°C - [ ] Cooling water valve type confirmed: **Proportional solenoid** (0–10 VDC, 5 L/min typical) - [ ] Valve response time measured: ~3–5 sec (note any delays) - [ ] All tag names verified against P&ID markup - [ ] Alarm thresholds reviewed: High warning 0.12, Trip 0.15 bar - [ ] HMI graphics wireframed and approved by shift supervisor - [ ] Data logging configured: pressure trend every 1 minute - [ ] Backup pressure gauge (mercury U-tube or calibrated analog) located for comparison ### On-Site Installation & Functional Test (2 days) **Day 1: Hardware Checkout** - [ ] Pressure transmitter calibrated: 0.08 bar = 12 mA ✓ - [ ] RTD sensor wells clean (no ice/detritus) - [ ] Cooling water pump operational (no cavitation noise) - [ ] Proportional valve solenoid energized: verify audible click at 5 VDC - [ ] Valve response to command: observe needle/spool movement manually - [ ] Electronic interlocks wired: trip signal to turbine control confirmed - [ ] Data historian receiving all values (no gaps >5 sec) - [ ] Alarms configured to annunciate on control room panel + email alert to operator **Day 2: Soft-Startup (Cold Condenser)** - [ ] Circulating pump running (monitor inlet temp rise) - [ ] Pressure trend chart displayed on HMI (should decay from 1.0 bar toward 0.08) - [ ] Time to reach 0.08 bar: record ____________ minutes (typical: 20–30) - [ ] Verify valve response: manually command 40% → observe outlet temp rise; then 70% → outlet temp drop - [ ] PID loop engaged: pressure remains within ±0.01 bar of setpoint - [ ] Valve hunting check: oscillation <±5% of command ### Commissioning (Hot Load Ramps, 5 days) **Day 3: Low-Load Stabilization (25% turbine load)** - [ ] Turbine ramped to 25% steam load (ca. 50 kg/s) - [ ] Pressure setpoint: 0.08 bar maintained ±0.005 bar for 30 minutes - [ ] Cooling valve position: ____ % (typical: 35–50% at low load) - [ ] Zero air ingress detected (pressure drift <±0.005 bar/5 min) ✓ - [ ] Fouling indicator: ≈ 0 (clean cooling tubes baseline) **Day 4: Medium-Load Verification (50% turbine load)** - [ ] Turbine load ramped to 50% steam flow - [ ] Pressure tracking setpoint: ±0.01 bar acceptable - [ ] Cooling delta-T: ___ °C (typical 8–10°C) - [ ] Valve response time: measure 0% → 100% command; pressure settles within ___ seconds - [ ] Confirm fouling index still <1 **Day 5: Full-Load Validation & Baseline Capture (100% turbine load)** - [ ] Turbine at rated load: ____ MW (record peak steam flow) - [ ] Pressure maintained at 0.080 ± 0.003 bar for 2 hours steady state - [ ] **BASELINE SNAPSHOT:** Record all parameters for 6-month fouling comparison - Pressure: __________ bar - Valve Position: __________ % - Cooling ΔT: __________ °C - Pump RPM: __________ - [ ] Pressure transient during load step (25% → 100%): peak 0.085, settles <30 sec ✓ - [ ] Check for intermittent air leaks: monitor for random pressure spikes - [ ] Fouling alarm threshold confirmed at baseline+2.0 points **Day 6–7: Stress & Edge Cases** - [ ] Cooling water flow interruption test: reduce pump speed 50% → pressure rises; verify high-pressure alarm - [ ] Manual valve closure test: command valve 100% (fully open) → verify pressure does not drop below 0.05 bar - [ ] Sensor fault injection: simulate stuck transmitter (stuck at 0.08) → verify system detects no response - [ ] Baseline archive: print chart, sign & date, file in commissioning folder --- ## 📊 Expected Performance ### Steady-State Metrics (Rated Load, Full-Power Operation) | Parameter | Target | Allowable Range | Typical Baseline | |-----------|--------|-----------------|-----------------| | **Condenser Pressure** | 0.080 bar | 0.075–0.085 bar | **0.0795 bar** | | **Pressure Stability** (oscillation) | ±0.003 bar | ±0.005 bar max | ±0.002 bar | | **Settling Time** (load step) | <30 sec | <60 sec max | ~18 sec | | **Cooling Valve Position** @ rated load | 55–65 % | 40–80 % | **62%** | | **Cooling Water ΔT** | 8–10 °C | 6–12 °C | **9.2°C** | | **Cooling Pump Flow** | 10,000 kg/s | 9,500–10,500 | **9,800 kg/s** | | **Turbine Power Loss** vs. design | <2% | <5% max | **0.8%** | ### Dynamic Response (Load Transients) **Turbine load: 0% → 100% (Full-speed ramp, 10%/min)** | Time (sec) | Load (%) | Pressure (bar) | Valve (%) | Trend | |-----------|----------|----------------|-----------|-------| | 0 | 0 | 0.095 | 25 | Baseline at idle | | 60 | 10 | 0.091 | 32 | P rising, pump adding heat | | 120 | 20 | 0.087 | 40 | Entering control band | | 180 | 30 | 0.084 | 48 | PID response active | | 240 | 40 | 0.082 | 54 | Approaching setpoint | | 300 | 50 | 0.081 | 58 | Good tracking | | 360 | 60 | 0.0805 | 60 | Tight control ±0.001 | | 420 | 70 | 0.0802 | 61 | Stable | | 480 | 80 | 0.0800 | 62 | Target reached ✓ | | 540 | 90 | 0.0798 | 63 | Minor overshoot | | 600 | 100 | 0.0799 | 63 | Steady-state ±0.002 | **Fouling Progression (Without Cleaning)** | Months Elapsed | Baseline Pressure (bar) | Valve Position (%) | ΔT Change (°C) | Notes | |----------------|-------------------------|-------------------|-----------------|-------| | 0 | 0.0795 | 62 | 9.2 ✓ | New/Clean tubes | | 3 | 0.0810 | 68 | 8.9 (↓0.3) | Light biofouling (seaweed) | | 6 | 0.0825 | 74 | 8.5 (↓0.7) | Moderate fouling — **Schedule cleaning** | | 9 | 0.0845 | 82 | 8.1 (↓1.1) | Heavy fouling — **Urgent** | | 12 | 0.0890 | 95 | 7.8 (↓1.4) | Cooling valve saturated — **Must clean NOW** | --- ## 🔄 Advanced Variations ### Variation A: Cooling Tower (Recirculating) vs. Once-Through River Water **Once-Through (River/Sea Water) — Described Above** - Pros: No fan power loss, minimal construction - Cons: Water temperature varies seasonally; biofouling risk (zebra mussels, algae); regulatory discharge thermal limits **Cooling Tower (Recirculating Air-Cooled)** - Condenser feeds cooling water to a fan-cooled tower; same water loops back - Tower outlet typically 10–15°C warmer → Higher condenser pressure - **New control node:** Cooling tower fan speed (VFD) replaces water valve control ``` High pressure → fanVFD↑ (more air through tower) → cooler water loops back ``` - Tower thermal capacity: larger lag (5–15 min) in response ### Variation B: Hybrid Vacuum System (With Hogging Turbo) For plants with air ingress risk or extreme fouling: - **Primary:** Cooling water valve + natural vacuum pump (centrifugal) - **Secondary:** "Hogging turbo" — small air extraction pump (screw or liquid-ring) energizes on startup - Hogging turbo pulls from hot well when pressure >0.12 bar - Once stabilized at 0.08, hogging turbo shuts down (saves parasitic power) ### Variation C: Predictive Fouling Index (Advanced) Instead of linear fouling accumulation, use Arrhenius temperature model: ``` Fouling Rate [kg/m²·hr] = k₀ × e^(−Eₐ/RT) × ΔT_approach k₀ = empirical constant (depends on water source: river, seawater, cooling tower) Eₐ = activation energy (~70 kJ/mol for typical bio-fouling) R = gas constant (8.314 J/mol·K) T = absolute temperature of bulk flow ΔT_approach = (inlet − condenser temp) — lower approach = more fouling propensityless fouling ``` Integrate over plant life → predict cleaning frequency (e.g., "Fouling will exceed 20% loss in 8.2 weeks"). --- ## 📄 Document Version History | Version | Date | Author | Change | |---------|------|--------|--------| | 1.0 | 2026-04-13 | Claude | Initial template: PID pressure control + fouling detection | --- *This template is part of the TSIMEREZIVO Industrial Process Control Library. For updates, contributions, or questions, contact the template maintainer.*

More like this

Rate, comment, and get full access

Members can download files, rate contributions, and discuss fixes with the engineers who posted them — free.

Join the library