Field fix / guideDesign DocumentVendor-agnostic (IEC 61131-3)Miningindustrial-automation

Crusher Jaw Gap & Feed Rate Optimization — Control Design

Shared by TSIMEREZIVO Team · 4 Oct 2026 · 43 views

# Mining Template: Crusher Jaw Gap & Feed Rate Optimization ## 1. Overview **Purpose:** A jaw crusher (belt-fed ore hopper → primary crusher → stockpile) must maintain optimal jaw gap (2–6 cm typical) to maximize throughput while preventing overload (motor stall, frame damage). Jaw gap is adjustable via eccentric pin or hydraulic actuator. Tight gap = fine product but lower throughput; loose gap = coarser product, higher throughput. The controller adjusts gap and feed rate to hit target size & capacity while protecting the motor. **Industry Standards:** - ISO 5474 (Vibrating Screens—Nomenclature) - DIN 22262 (Jaw Crushers—Design, Performance, Safety) - ASME B29 (Belt Drive Friction Equipment) **Critical Constraints:** - **Jaw gap range:** minimum 20 mm (fine), maximum 60 mm (coarse); adjust via eccentric pin rotation or pilot hydraulics - **Motor current limit:** if current > 90% rated during crushing, gap too tight; open wider - **Throughput:** kg/hour inversely related to fineness; tighter gap = lower throughput - **Liner wear:** tighter gap = more energy, faster liner dulling; predictive maintenance via wear rate trending - **Vibration & noise:** loose gap allows more chattering; monitor for bearing health - **Discharge blinding:** fine product must not jam chute; gravity alone insufficient; may need chute vibration **Relevant Physics:** - **Crusher power:** $P = k \times f(D) \times Q$ where f(D) = function of particle size, Q = throughput - **Momentum transfer:** jaw closes at speed $v_{jaw}$; impact energy $E = \frac{1}{2}m v_{jaw}^2$ (depends on gap opening speed) - **Force transmission:** crushing force $F = \tau / d_{lever}$ (torque ÷ jaw lever arm) - **Wear rate:** $\partial h / \partial t \propto$ energy per particle; tighter gap = higher wear --- ## 2. Control Philosophy ``` LAYER 1: Jaw Gap Position Feedback LVDT sensor monitors eccentric pin position Setpoint: reference gap for target product size Feedback: every scan LAYER 2: Motor Current Monitoring If current > 85%: gap getting clogged; open wider If current < 50%: underutilized; reduce gap or increase feed Adjust gap proportionally to maintain 70% nominal current LAYER 3: Feed Rate Cascade Feed rate setpoint adjusted based on product grade required If jaw gap wide (coarse): accept higher feed If jaw gap tight (fine): reduce feed to prevent stall LAYER 4: Wear Trending Track motor current over time for same gap setting If current rises (same gap, same feed) → liner wear → increase gap proportionally Predict liner replacement when wear exceeds threshold LAYER 5: Discharge Monitoring Monitor discharge chute vibration or photoelectric sensor If discharge blocked → reduce feed until chute clears If discharge flowing freely → can increase feed ``` --- ## 3. Control Logic (Condensed) ```pascal { === CRUSHER JAW GAP & FEED RATE OPTIMIZATION === } PROCEDURE Crusher_Control_Master CONSTANTS RATED_MOTOR_CURRENT_A = 150 CURRENT_NOMINAL_PCT = 70 { 105 A = efficient } CURRENT_ALARM_PCT = 85 { 127.5 A = overload warning } CURRENT_TRIP_PCT = 95 { emergency stop } JAW_GAP_MIN_MM = 20 { fine product limit } JAW_GAP_MAX_MM = 60 { coarse product limit } JAW_GAP_NOMINAL_MM = 40 { mid-range } FEED_RATE_MIN_T_HR = 5 FEED_RATE_MAX_T_HR = 50 { hopper capacity } LINER_WEAR_THRESHOLD_MM = 25 { total wear before replace } VARIABLES jaw_gap_measured_mm : REAL { LVDT sensor } jaw_gap_setpoint_mm : REAL motor_current_a : REAL motor_current_pct : REAL current_error_pct : REAL { vs. nominal 70% } feed_rate_measured_t_hr : REAL { belt scale } feed_rate_setpoint_t_hr : REAL motor_speed_rpm : REAL { motor feedback } discharge_rate_t_hr : REAL { estimated from speed × product } liner_wear_current_baseline_a : REAL { baseline current for nominal gap } liner_wear_mm : REAL { cumulative wear } liner_wear_trend_a_per_hour : REAL discharge_blocked : BOOLEAN { photoelectric or vibration check } crusher_status : ENUMERATION { NORMAL | OVERLOAD | UNDERUTILIZED | BLOCKED | WORN } BEGIN { === SENSOR INPUT === } jaw_gap_measured_mm = Read_Gap_LVDT_Transducer() motor_current_a = Read_Motor_Current() motor_speed_rpm = Read_Motor_Speed() discharge_blocked = Check_Discharge_Blockage() motor_current_pct = (motor_current_a / RATED_MOTOR_CURRENT_A) × 100 { === PRODUCT SIZE & FEED RATE STRATEGY === } { Product fineness inversely related to jaw gap } { Operator sets desired product grade; controller derives gap & feed } product_grade_setpoint = Read_Operator_Grade_Select() { 1=coarse, 10=fine } jaw_gap_setpoint_mm = JAW_GAP_MAX_MM − (product_grade_setpoint × 4) { 60 to 20 mm } { === JAW GAP CONTROL === } gap_error_mm = jaw_gap_setpoint_mm − jaw_gap_measured_mm { Proportional control to adjust eccentric pin } IF ABS(gap_error_mm) > 2 THEN gap_motor_cmd_pct = 50 + (gap_error_mm × 5) { 5%/mm sensitivity } Command_Gap_Actuator(gap_motor_cmd_pct) Log_Info("JAW_GAP_ADJUSTING", target=jaw_gap_setpoint_mm, current=jaw_gap_measured_mm) END IF { === MOTOR LOAD CONTROL === } current_error_pct = CURRENT_NOMINAL_PCT − motor_current_pct { If motor overloaded: widen gap to reduce crushing force } IF motor_current_pct > CURRENT_ALARM_PCT THEN jaw_gap_setpoint_mm = jaw_gap_setpoint_mm + 2 { open gap by 2 mm } crusher_status = OVERLOAD Log_Warning("CRUSHER_OVERLOAD_GAP_OPENING", current_pct=motor_current_pct) { If underutilized: tighten gap or increase feed } ELSIF motor_current_pct < 50 THEN jaw_gap_setpoint_mm = jaw_gap_setpoint_mm − 1 { close gap by 1 mm } crusher_status = UNDERUTILIZED END IF { Emergency stop on severe overload } IF motor_current_pct > CURRENT_TRIP_PCT THEN crusher_status = OVERLOAD Log_Alarm("CRUSHER_STALL_EMERGENCY_STOP", current_pct=motor_current_pct) Command_Motor_Stop() jaw_gap_setpoint_mm = JAW_GAP_MAX_MM { fully open } END IF { === FEED RATE CASCADE === } { Normalize feed based on gap and target throughput } { Wider gap → accept higher feed; tighter gap → reduce feed } gap_factor = jaw_gap_measured_mm / JAW_GAP_NOMINAL_MM target_feed_t_hr = 30 × gap_factor { base 30 t/hr at nominal gap } feed_rate_setpoint_t_hr = target_feed_t_hr { Clamp to safe limits } IF feed_rate_setpoint_t_hr < FEED_RATE_MIN_T_HR THEN feed_rate_setpoint_t_hr = FEED_RATE_MIN_T_HR END IF IF feed_rate_setpoint_t_hr > FEED_RATE_MAX_T_HR THEN feed_rate_setpoint_t_hr = FEED_RATE_MAX_T_HR END IF Command_Belt_Drive_Setpoint(feed_rate_setpoint_t_hr) { === DISCHARGE BLOCKAGE DETECTION === } IF discharge_blocked = TRUE THEN crusher_status = BLOCKED Log_Alarm("DISCHARGE_CHUTE_BLOCKED") { Reduce feed or run crusher in reverse briefly } feed_rate_setpoint_t_hr = feed_rate_setpoint_t_hr × 0.5 { After 30 sec, try forward again } WAIT 30000_ms discharge_blocked = Check_Discharge_Blockage() { re-check } IF discharge_blocked = FALSE THEN feed_rate_setpoint_t_hr = target_feed_t_hr { restore } END IF END IF { === LINER WEAR TRENDING === } { As liners wear, more force needed for same gap → current rises } { Detect wear by monitoring current vs. baseline at same gap } IF MOD(scan_count, 3600) = 0 THEN { every hour } current_for_gap = motor_current_a { If gap unchanged but current up, likely wear } IF current_for_gap > liner_wear_current_baseline_a + 10 THEN liner_wear_mm = liner_wear_mm + 0.5 { estimate 0.5 mm/hour wear } liner_wear_trend_a_per_hour = (current_for_gap − liner_wear_current_baseline_a) / (liner_wear_mm + 0.1) IF liner_wear_mm > LINER_WEAR_THRESHOLD_MM THEN crusher_status = WORN Log_Alarm("CRUSHER_LINER_WORN_SCHEDULE_REPLACEMENT", wear_mm=liner_wear_mm) END IF END IF END IF { === DATA LOGGING (every 15 min) === } IF MOD(scan_count, 900) = 0 THEN Log_Process_Data({ timestamp: Get_Timestamp(), jaw_gap_mm: jaw_gap_measured_mm, motor_current_pct: motor_current_pct, feed_rate_t_hr: feed_rate_measured_t_hr, discharge_rate_t_hr: discharge_rate_t_hr, crusher_status: crusher_status, liner_wear_mm: liner_wear_mm, motor_speed_rpm: motor_speed_rpm }) END IF END PROCEDURE ``` --- ## 4. Tag List ``` JAW_GAP_MEASURED_MM { LVDT position feedback } JAW_GAP_SETPOINT_MM { target gap control } JAW_GAP_ACTUATOR_CMD_PCT { motor position command } MOTOR_CURRENT_A { load indicator } MOTOR_CURRENT_PCT { normalized feedback } MOTOR_SPEED_RPM { motor speed } FEED_RATE_MEASURED_T_HR { belt scale input } FEED_RATE_SETPOINT_T_HR { cascade target } DISCHARGE_BLOCKED { blockage sensor } PRODUCT_GRADE_SETPOINT { 1=coarse, 10=fine } LINER_WEAR_MM { cumulative wear } CRUSHER_STATUS { NORMAL|OVERLOAD|WORN|BLOCKED } DISCHARGE_RATE_T_HR { estimated throughput } ``` --- ## 5. Alarm & Trip Matrix | **Condition** | **Severity** | **Action** | |---|---|---| | **Current > 85%** | ⚠ WARN | Open jaw gap 2 mm | | **Current > 95%** | 🔴 CRIT | Stop motor; open jaw to max | | **Discharge blocked** | 🔴 CRIT | Reduce feed 50%; check hopper | | **Liner wear > threshold** | 🟡 WARN | Schedule liner replacement | | **Underloaded (<50%)** | ⚠ WARN | Close gap or increase feed | --- **Document Version:** 1.0 **Last Updated:** 2026-04-13 **Status:** Ready for Production

More like this

Rate, comment, and get full access

Members can download files, rate contributions, and discuss fixes with the engineers who posted them — free.

Join the library