Field fix / guideDesign DocumentVendor-agnostic (IEC 61131-3)Power Plantindustrial-automation

Boiler Feedwater Pump Pressure Control — Control Design

Shared by TSIMEREZIVO Team · 4 Oct 2026 · 42 views

# TSIMEREZIVO Template: Boiler Feedwater Pump Pressure Control **Category:** Power Plant | **Industry:** Thermal Power Generation | **Language:** Ladder / Structured Text --- ## 📋 Overview ### Purpose Maintain boiler feedwater pump discharge pressure at precisely 180–200 bar to overcome boiler steam drum pressure (175 bar at design) plus pipe friction losses (~15–20 bar) while minimizing energy waste. Too high = relief valve spills energy; too low = boiler couldn't fill; too dynamic = oscillations excite piping resonance. ### Typical Application - **Pump Type:** Multi-stage centrifugal; 50–300 MW thermal plant - **Nominal Capacity:** 100–250 kg/s feed flow (scales with plant output) - **Pump Suction (from deaerator):** 0.3–0.5 bar absolute - **Discharge Pressure Target:** 185 bar (nominal) - **Bypass/Relief Valve:** Set to 200 bar (protects pump, wasteful if used continuously) - **VFD Motor Drive:** Allows speed modulation OR fixed-speed pump with proportional bypass valve ### Why This Matters Feedwater pressure is the **third most-critical control** (after turbine speed and condenser vacuum): - **Under-pressure:** Boiler drum level drops (cavitation cascade → dangerous) - **Over-pressure:** Relief valve continuously dumps → $50K–$100K/day wasted steam energy - **Instability:** Pressure oscillations couple to boiler level swell/shrink → loss of control A well-tuned pump pressure controller saves **2–4% plant efficiency** vs. a constantly-relieving bypass system. --- ## 🎯 Control Philosophy ### Key Equations **Pump Discharge Pressure Balance:** ``` P_discharge = P_suction + ΔP_pump − losses Where: P_suction = 0.4 bar absolute (deaerator head) ΔP_pump = f(N²) where N = pump RPM ≈ 180 bar at rated speed (100 MW plants) losses = pipe friction, check valve (2–5 bar typically) P_discharge = 0.4 + 180 − 3.5 = 176.9 bar (nominal) + boiler safety margin = 185 bar setpoint Density correction (hot water at 160°C): ρ = 842 kg/m³ (vs. 1000 kg/m³ at 20°C) → 16% less dense P_real = P_nominal × (ρ_160 / ρ_20) × (correction factor) ``` **Pump Head-Capacity Curve (Centrifugal):** ``` H [bar] = a − b × Q² + c × N²/1000 Where Q = volume flow (m³/h), N = speed (RPM) Typical: H = 200 − 0.15×Q² + 1.8×(N/3000)² At 2850 RPM, 100 m³/h: H = 200 − 0.15×(100)² + 1.8×(2850/3000)² = 182 bar ✓ ``` **Pump Affinity Laws (for VFD-driven pumps):** ``` Q ∝ N (flow proportional to speed) H ∝ N² (head proportional to speed square) Power ∝ N³ (power cubic — why VFD saves energy) Reducing RPM from 3000 → 2850 (95%): Flow reduces to 95% (OK, matches lower load) Head reduces to 95²% = 90.25% (still sufficient) Power reduces to 95³% = 85.7% (20% less motor power! ✓) ``` **Control Strategy: Pressure Feedback Loop** ``` Load Demand │ ▼ Boiler drum level low? / YES ─→ [Increase pump speed/pressure] / / NO / Pressure feedback │ ├─ If P_discharge > 200 bar → Relief opens → Waste │ ├─ If P_discharge < 170 bar → Boiler can't fill │ └─ If P_discharge = 185 bar → Optimal (just overcome resistance) Two Implementation Options: A) FIXED-SPEED PUMP + PROPORTIONAL BYPASS RELIEF Simple, robust; ~5% continuous energy loss (relief valve open) B) VFD-DRIVEN PUMP + CLOSED-LOOP PRESSURE PID Complex, high-efficiency; can achieve <1% loss Modern plant standard → build this version ``` ### Control Loop: VFD Speed Modulation with Pressure Feedback ``` Boiler water level / load demand │ ┌────────┴────────┐ ▼ ▼ P_discharge sensor Flow demand │ │ ├─────────────────┤ │ │ ▼ ▼ [PID] [Feedforward] │ │ ├─────────────────┤ │ ▼ VFD Speed Command (RPM) │ ▼ Pump speed increases/decreases → Head (ΔP) changes via N² law → Pressure setpoint reached → Relief valve stays closed ✓ ``` **PID Loop Tuning:** - **Proportional Gain (Kp):** 0.05 — moderate response (pressure is slow thermal lag) - **Integral Gain (Ki):** 0.003 — gentle correction (pump thermal mass is large) - **Derivative (Kd):** 0 — NO derivative (causes hunting on pressure spikes) Why gentle tuning? Pump thermodynamic response is slow (5–15 second lag from RPM change to final pressure). --- ## 🏗️ Control Logic ### Pseudocode: Boiler Feedwater Pump Pressure Control (VFD-Driven) ```pascal PROGRAM BoilerFeedwaterPumpPressureControl; { ========== DECLARATIONS ========== } VAR -- INPUT SENSORS pump_discharge_pressure : REAL; { 0-250 bar, 4-20 mA transmitter } pump_discharge_temperature : REAL; { 100-180 °C, RTD input } pump_suction_pressure : REAL; { 0-1 bar absolute, low-range sensor } pumpm_speed_feedback : REAL; { 0-3600 RPM, tachometer } pump_motor_current : REAL; { 0-500 A, current transducer } boiler_drum_level : REAL; { 0-100 %, for load indication } boiler_steam_pressure : REAL; { 0-250 bar, main steam pressure } relief_valve_position : REAL; { 0-100 %, bypass flow feedback or direct measurement } -- CONTROL SETPOINTS pump_pressure_sp : REAL := 185.0; { Target discharge pressure } pump_pressure_alarm_high : REAL := 210.0; { Over-pressure warning } pump_pressure_trip_high : REAL := 215.0; { Relief valve stuck open? } pump_pressure_alarm_low : REAL := 165.0; { Under-pressure warning } pump_pressure_trip_low : REAL := 155.0; { Critical low } relief_valve_cracking : REAL := 200.0; { Relief setpoint (fixed) } -- CONTROL LOOP STATE pressure_error : REAL; pressure_error_integral : REAL := 0.0; pressure_prev : REAL := 185.0; -- VFD COMMAND vfd_speed_command_rpm : REAL; vfd_speed_limited : REAL; vfd_speed_rate_limit : REAL := 10.0; { Max RPM/sec change } vfd_speed_command_prev : REAL := 3000.0; -- PID TUNING kp_pump : REAL := 0.05; { Proportional: slow response } ki_pump : REAL := 0.003; { Integral: minimum for slow plant } kd_pump : REAL := 0.0; { NO derivative (oscillation risk) } integral_limit_hi : REAL := 50.0; { Max +integral output: ±50 RPM } integral_limit_lo : REAL := -50.0; scan_time : REAL := 1.0; { 1-second scan (faster than deaerator) } -- FEEDFORWARD TERM (Optional enhancement) boiler_load_percent : REAL; ff_speed_base : REAL; { RPM to just overcome static head } -- ENERGY MONITORING relief_valve_flow_est : REAL; { Estimated flow being dumped } wasted_power_mw : REAL; { Power dissipated in relief } -- PRESSURE QUALITY INDICATORS pressure_oscillation_pk : REAL := 0.0; { Track peak oscillation } pressure_stability_index : REAL := 0.0; { Increasing = getting worse } -- OUTPUT COMMANDS vfd_frequency_command : REAL; { 0-60 Hz output to VFD drive } BEGIN { ========== SENSOR ACQUISITION & DIAGNOSIS ========== } -- Calculate pump delta-P (head generated) pump_head_bar := pump_discharge_pressure - pump_suction_pressure; -- Estimate relief valve flow (if relief cracked open) -- Relief opens at 200 bar; discharge trying to go higher IF pump_discharge_pressure > relief_valve_cracking THEN relief_valve_flow_est := (pump_discharge_pressure − relief_valve_cracking) × 0.5; { Rough estimate } ELSE relief_valve_flow_est := 0.0; END_IF; -- Estimate wasted power (relief dissipation) wasted_power_mw := (relief_valve_flow_est [kg/s] × 0.001 [m³/kg] × (pump_discharge_pressure − 1) [bar]) / 25; { ========== ERROR CALCULATION ========== } pressure_error := pump_pressure_sp - pump_discharge_pressure; { ========== FEEDFORWARD INITIALIZATION ========== } -- Estimate required pump speed based on boiler load level -- At full load: ~185 bar needed. At light load: ~170 bar is sufficient. boiler_load_percent := boiler_drum_level; { Proxy for demand } -- Base speed needed to overcome static delta-P (boiler steam − suction + friction) static_dp_required := (boiler_steam_pressure − pump_suction_pressure) + 10.0; { ~10 bar friction margin } -- Using N² law: N required ∝ sqrt(P required) ff_speed_base := 3000.0 × SQRT(static_dp_required / 185.0); { ~2850–2950 RPM @ full load, adjusted for pressure } { ========== PROPORTIONAL CONTROL ========== } -- Smooth proportional term: negative error (too much pressure) → reduce RPM proportional_term := kp_pump * pressure_error; { In RPM units } { ========== INTEGRAL CONTROL (Slow Correction) ========== } -- Integral only adjusts for steady-state offset (e.g., seasonal density changes) integral_term := integral_term + (ki_pump * pressure_error * scan_time); -- Anti-windup IF integral_term > integral_limit_hi THEN integral_term := integral_limit_hi; ELSIF integral_term < integral_limit_lo THEN integral_term := integral_limit_lo; END_IF; { ========== COMBINED VFD COMMAND ========== } -- Base speed (feedforward) + proportional adjustment + integral trim vfd_speed_command_rpm := ff_speed_base + proportional_term + integral_term; { ========== RATE LIMITING (Anti-Shock) ========== } -- Prevent sudden speed swings that would cause pressure spikes speed_delta := vfd_speed_command_rpm - vfd_speed_command_prev; max_delta := vfd_speed_rate_limit * scan_time; IF speed_delta > max_delta THEN vfd_speed_limited := vfd_speed_command_prev + max_delta; ELSIF speed_delta < -max_delta THEN vfd_speed_limited := vfd_speed_command_prev - max_delta; ELSE vfd_speed_limited := vfd_speed_command_rpm; END_IF; { ========== HARD OUTPUT LIMITS ========== } -- Pump physical limits: 800 RPM (minimum stable) to 3600 RPM (motor nameplate) IF vfd_speed_limited < 800.0 THEN vfd_speed_limited := 800.0; ELSIF vfd_speed_limited > 3600.0 THEN vfd_speed_limited := 3600.0; END_IF; { ========== CONVERT RPM TO VFD FREQUENCY ========== } -- Standard formula: Frequency [Hz] = RPM / 120 × Poles -- For 4-pole motor (60 Hz = 1800 RPM): Frequency = RPM × 60 / 1800 = RPM / 30 -- For 2-pole motor (60 Hz = 3600 RPM): Frequency = RPM / 60 -- Assume 2-pole: 3000 RPM = 50 Hz vfd_frequency_command := (vfd_speed_limited / 3000.0) × 50.0; { Scale to 50 Hz nominal } { ========== ALARMS & CHECKS ========== } -- Check 1: Over-pressure (relief cracked open) IF pump_discharge_pressure > pump_pressure_alarm_high THEN { WARN: "Pump discharge pressure high — {value} bar" } END_IF; IF pump_discharge_pressure > pump_pressure_trip_high THEN { ALARM: "Pump pressure critical — relief stuck OPEN? Check for blockage downstream" } END_IF; -- Check 2: Under-pressure (VFD maxed out? Suction issue?) IF pump_discharge_pressure < pump_pressure_alarm_low THEN { WARN: "Pump discharge pressure low — {value} bar" } END_IF; IF pump_discharge_pressure < pump_pressure_trip_low THEN { ALARM: "Pump pressure CRITICAL — Boiler cannot be filled. Check pump suction (deaerator level?)" } END_IF; -- Check 3: VFD at maximum but still under-pressure? IF vfd_speed_limited >= 3600.0 AND pump_discharge_pressure < 170.0 THEN { ALARM: "VFD saturated at max speed but pump still weak — pump cavitation or impeller wear?" } END_IF; -- Check 4: Pressure oscillating excessively? pressure_change := ABS(pump_discharge_pressure - pressure_prev) / scan_time; pressure_oscillation_pk := MAX(pressure_oscillation_pk, pressure_change); IF pressure_oscillation_pk > 2.0 THEN { Bar/sec oscillation } { ALARM: "Pump pressure hunting — tuning adjustment needed or relief valve chattering" } END_IF; -- Check 5: Wasted power (relief open too much) IF wasted_power_mw > 5.0 AND boiler_load_percent > 80.0 THEN { ALARM: "Excessive relief flow — adjust VFD response or check relief setpoint" } { This is costing $50K/day per MW wasted! } END_IF; -- Check 6: Pump motor overheating? IF pump_motor_current > 450.0 A THEN { WARN: "Pump motor current high — {value} A — check water temperature and viscosity" } END_IF; -- Check 7: Suction pressure too low (cavitation risk)? IF pump_suction_pressure < 0.2 THEN { ALARM: "Pump suction pressure critically low — deaerator level in trouble?" } END_IF; { ========== ENERGY EFFICIENCY LOG ========== } -- Record % of time relief valve is open -- Goal: < 1% relief valve operation at steady state IF relief_valve_flow_est > 1.0 THEN { More than 0.1 kg/s wasted } relief_open_time += scan_time; END_IF; relief_open_percentage := (relief_open_time / total_time) × 100.0; IF relief_open_percentage > 5.0 THEN { ACTION: "Review pump VFD tuning — relief operating >5% of time (poor efficiency)" } END_IF; { ========== UPDATE STATE FOR NEXT CYCLE ========== } pressure_prev := pump_discharge_pressure; vfd_speed_command_prev := vfd_speed_limited; { ========== SEND COMMAND ========== } -- Output: vfd_frequency_command (0-50 Hz output to VFD drive) -- Output: pressure feedback for HMI display END_PROGRAM; ``` --- ## 🏷️ Tag List ### Analog Inputs (Sensors) | Tag Name | Type | Range | Units | Description | |----------|------|-------|-------|-------------| | `PUMP_DISCHARGE_PRESSURE` | AI | 0–250 | bar | Main feedwater pump discharge (4-20 mA) | | `PUMP_DISCHARGE_TEMP` | AI | 0–180 | °C | Discharge temperature (density compensation) | | `PUMP_SUCTION_PRESSURE` | AI | 0–1 | bar abs | Suction from deaerator (low-range sensor) | | `PUMP_SPEED_FEEDBACK` | AI | 0–3600 | RPM | Pump shaft speed tachometer | | `VFD_OUTPUT_FREQUENCY` | AI | 0–60 | Hz | VFD actual frequency output (feedback) | | `PUMP_MOTOR_CURRENT` | AI | 0–500 | A | Motor phase-to-neutral current | | `BOILER_STEAM_PRESSURE` | AI | 0–250 | bar | Main steam header pressure (for load indication) | | `RELIEF_VALVE_POSITION` | AI | 0–100 | % | Bypass valve crack opening (if available) | ### Analog Outputs (Command) | Tag Name | Type | Range | Units | Description | |----------|------|-------|-------|-------------| | `PUMP_PRESSURE_SP` | REAL | 160–200 | bar | Setpoint (fixed or scheduled) | | `PUMP_PRESSURE_ERROR` | REAL | −50 to +50 | bar | Error = SP − Actual | | `VFD_FREQUENCY_COMMAND` | AO | 0–60 | Hz | 0-10 VDC output to VFD drive electronics | | `VFD_SPEED_COMMAND` | REAL | 600–3600 | RPM | Desired pump speed (intermediate variable) | | `RELIEF_ESTIMATED_FLOW` | REAL | 0–300 | kg/s | Calculated bypass flow (diagnostic) | | `WASTED_POWER_MW` | REAL | 0–10 | MW | Power dissipated in relief valve | ### Discrete Signals | Tag Name | Type | Logic | Description | |----------|------|-------|-------------| | `PUMP_PRESSURE_HI_WARN` | DO | Latched | Pressure > 210 bar (warning) | | `PUMP_PRESSURE_HI_TRIP` | DO | Latched | Pressure > 215 bar (critical) | | `PUMP_PRESSURE_LO_WARN` | DO | Latched | Pressure < 165 bar (check suction) | | `PUMP_PRESSURE_LO_TRIP` | DO | Latched | Pressure < 155 bar (boiler cannot fill) | | `VFD_AT_MAX_SPEED` | DO | Auto | VFD frequency = 50 Hz (saturated) | | `RELIEF_VALVE_OPEN` | DO | Calculated | Relief valve flow > 1 kg/s | | `PUMP_CAVITATION_RISK` | DO | Auto | Suction pressure < 0.2 bar | | `MOTOR_OVERTEMP_RISK` | DO | Latched | Motor current > 450 A for >5 min | | `PRESSURE_HUNTING` | DO | Latched | Oscillation rate > 2 bar/sec | --- ## 🚨 Alarm & Trip Matrix | Condition | Threshold | Severity | Action | Recovery | |-----------|-----------|----------|--------|----------| | **Pressure High (Warn)** | > 210 bar | ⚠️ WARN | Monitor; check relief seat for leakage | <200 bar | | **Pressure High (Trip)** | > 215 bar | 🔴 TRIP | Stop pump; inspect relief valve | Relief repair needed | | **Pressure Low (Warn)** | < 165 bar | ⚠️ WARN | Check deaerator level; boost VFD if possible | >170 bar | | **Pressure Low (Trip)** | < 155 bar | 🔴 TRIP | Reduce load; fill boiler from auxiliary pump | Investigate root cause | | **Relief Valve Stuck** | Pressure > 200 bar + relief open | 🔴 CRIT | Bypass valve cartridge stuck; manual operation | Disassemble/clean relief | | **Pump Cavitation** | Suction < 0.2 bar + noise | 🔴 CRIT | Boost deaerator level; check for restrictions | Deaerator repair | | **VFD Saturated** | Speed = 3600 + P < 170 bar | 🔴 CRIT | Pump impeller damaged or very worn | Pump inspection/replacement | | **Pressure Hunting** | Oscillation > 2 bar/sec | ⚠️ WARN | PID tuning issue or relief chattering | Retune Kp/Ki or clean relief | | **Relief Excessive** | >5% duty cycle | ⚠️ WARN | Energy waste ($50K+/day); tuning degraded | Retune VFD loop | | **Motor Overload** | Current > 450 A sustained | ⚠️ WARN | Check water temperature & viscosity | Cool discharge water | --- ## 📺 HMI Layout ### Pump Pressure & VFD Control Panel ``` ┌────────────────────────────────────────────────────────┐ │ BOILER FEEDWATER PUMP PRESSURE & SPEED CONTROL │ ├────────────────────────────────────────────────────────┤ │ │ │ ╔══════════ PRESSURE STATUS ══════════╗ │ │ ║ Discharge: 184.5 bar ║ │ │ ║ Setpoint: 185.0 bar ║ │ │ ║ Error: −0.5 bar (nominal) ║ │ │ ║ ║ │ │ ║ Suction: 0.39 bar (OK ✓) ║ │ │ ║ Relief: 200 bar (CLOSED ✓) ║ │ │ ║ ║ │ │ ║ Trend: ▃▃▃▃▄▄▄▄▅ stable ║ │ │ ╚═════════════════════════════════════╝ │ │ │ │ ╔══════════ VFD SPEED ═════════════════╗ │ │ ║ Command: 2985 RPM ║ │ │ ║ Feedback: 2984 RPM (sync ✓) ║ │ │ ║ Frequency: 49.7 Hz ║ │ │ ║ Motor Load: 385 A (77% rated) ║ │ │ ║ Power Out: 3.8 MW ║ │ │ ╚═══════════════════════════════════════╝ │ │ │ │ ╔════════ EFFICIENCY METRICS ═════════╗ │ │ ║ Relief Flow: 0 kg/s (0% duty) ║ │ │ ║ Wasted Power: 0 MW (optimal!) ║ │ │ ║ Uptime Today: 16 hours ✓ ║ │ │ ║ Relief Ops: < 1% excellent ║ │ │ ╚════════════════════════════════════════╝ │ │ │ │ ⚠️ [NONE] 🔴 [NONE] │ │ │ │ [ Load: 75% ] [ Set Pressure: 185.0 ▼ ] │ │ │ └────────────────────────────────────────────────────────┘ ``` ### 24-Hour Pressure Trend with Relief History ``` Pressure [bar] 220 ├─ Relief setpoint 210 ├────────────────────────────────────────────── 200 ├──╱╲ ╱╲ 190 ├─╱ ╲────────╱ ╲───────────────── 180 ├/────────────────────────────────── ← Setpoint 170 ├──────────────────────────────────── 160 └──00:00──06:00──12:00──18:00──00:00 Relief Flow [kg/s] 5 ├─╱ ╲ ╱ ╲ 0 └───────────────────────────── ← Closed Observations: - Morning load ramp (05:00–08:00): Relief briefly opens 1 kg/s - Midday (10:00–18:00): Relief closed (tuning good) - Evening peak (19:00–20:00): Relief spikes to 3 kg/s (suboptimal) ``` --- ## 🔧 Configuration Parameters ```json { "boiler_feedwater_pump": { "description": "Feedwater pump discharge pressure PID with VFD speed control", "nominal_setpoint_bar": 185.0, "scan_time_sec": 1.0, "pid_tuning": { "proportional_gain_kp": 0.05, "integral_gain_ki": 0.003, "derivative_gain_kd": 0.0, "integral_limit_hi_rpm": 50.0, "integral_limit_lo_rpm": -50.0 }, "vfd_limits": { "min_speed_rpm": 800.0, "max_speed_rpm": 3600.0, "rate_limit_rpm_per_sec": 10.0, "nominal_motor_poles": 2, "nominal_frequency_hz": 50.0 }, "pressure_alarms": { "high_warning_bar": 210.0, "high_trip_bar": 215.0, "low_warning_bar": 165.0, "low_trip_bar": 155.0, "relief_valve_setpoint_bar": 200.0 }, "feedforward": { "base_speed_calculation": "N = 3000 * sqrt(P_static_required / 185)", "load_compensation": true, "seasonal_density_correction": true }, "efficiency_monitoring": { "relief_open_threshold_kg_per_sec": 1.0, "max_wasted_power_threshold_mw": 5.0, "target_relief_duty_cycle_percent": 1.0 }, "commissioning": { "min_discharge_pressure_at_full_load_bar": 175.0, "target_margin_above_steam_pressure_bar": 10.0, "expected_vfd_frequency_at_full_load_hz": 49.0 } } } ``` --- ## 📝 Implementation Checklist ### Pre-Commissioning Design (1 day) - [ ] Pump curve provided by manufacturer: head vs. flow at various speeds - [ ] VFD drive rated for motor: kW rating ≥ pump motor nameplate - [ ] Relief valve interlocked: opens only if discharge > 200 bar (no continuous bypass) - [ ] Pressure transmitters installed: discharge (0–250 bar primary) + suction (0–1 bar secondary) - [ ] Tachometer on pump shaft verified: 0–3600 RPM feedback - [ ] Current transducer on motor: phase current measurement - [ ] PID tuning baseline selected: Kp = 0.05, Ki = 0.003 (conservative) - [ ] Affinity law calculations verified: N² relationship for head - [ ] Alarm setpoints reviewed: high 210 bar, low 165 bar ### On-Site Installation (2 days) **Day 1: Hardware & Electrical** - [ ] VFD drive mounted, power wiring verified (3-phase 480V typical) - [ ] Pump motor soft-start tested: no inrush current spike >1.5× nameplate - [ ] Pressure transmitters calibrated: discharge at 185 bar = 12 mA output - [ ] Tachometer signal verified: 3000 RPM = 50 Hz output - [ ] PLC analog cards configured: 0–250 bar pressure input card, 0–60 Hz VFD output - [ ] All interlocks wired: relief input, deaerator low-level signal **Day 2: Control Loop Commissioning (Pump pressurised, not running)** - [ ] Manual VFD test: command 20 Hz → observe pump speed rises smoothly - [ ] Stop pump; increase command to 50 Hz; pressure visible on gauge - [ ] Verify relief valve response: manually increase until relief cracks at 200 bar ✓ - [ ] Check proportional/integral response: small command change causes smooth pressure shift ### Hot Commissioning (4 days at power plant) **Day 3: Soft-Start (Deaerator filled, pump to atmosphere)** - [ ] Start pump at 10 Hz (low speed): pressure rises to ~20 bar (no load) - [ ] Gradually increase to 50 Hz: pressure rises to ~180 bar (expected) - [ ] Monitor discharge temperature: should NOT exceed 80°C at 50 Hz (no boiler backpressure yet) - [ ] Zero cavitation noise: suction pressure stable >0.3 bar ✓ - [ ] Relief valve tested: increase speed until relief cracks → observe smooth bypass flow **Day 4: Load Coupling (Connect to boiler steam drum at low pressure)** - [ ] Boiler drum at 20 bar: pump delivers feed water at 30 bar discharge (easy) - [ ] Pressure setpoint engaged: PID loop now active - [ ] Monitor pressure oscillation: should settle within ±2 bar within 30 seconds - [ ] Observe VFD speed adjustment: as drum pressure rises, VFD speed increases to maintain 185 bar SP - [ ] Temperature rise at discharge: note baseline (typically +8–12°C rise across pump) **Day 5: Full-Load Ramp Validation (100% steam generation)** - [ ] Boiler steam pressure ramped to 175 bar (design pressure) - [ ] Pump discharge pressure holds at 185 bar ±3 bar (acceptable tolerance) - [ ] VFD frequency: ____ Hz (note baseline, typically 48–50 Hz) - [ ] Motor current: ____ A (note baseline for future monitoring) - [ ] Relief valve: CLOSED (no flow, 0% duty cycle) ✓ - [ ] **BASELINE CAPTURE:** - VFD Frequency @ full load: ___ Hz - Motor current @ full load: ___ A - Discharge temp @ full load: ___ °C - Pump suction pressure @ full load: ___ bar - [ ] 2-hour stability run at constant load: zero relief operation, steady pressure **Day 6–7: Transient & Fault Testing** - [ ] Load increase (25% → 100%): relief stays closed; pressure holds <3 bar overshoot - [ ] Load decrease (100% → 25%): pressure undershoots <2 bar; recovers in <30 sec - [ ] Deaerator low-level alarm: pump suction pressure drops; controller reduces speed - [ ] Manual relief bypass flow test: close outlet valve; relief opens; observe smooth energy dissipation - [ ] VFD frequency tracking: check feedback = command within 1 Hz --- ## 📊 Expected Performance ### Steady-State Performance (Full-Load Operation) | Parameter | Target | Allowable | Typical | |-----------|--------|-----------|---------| | **Discharge Pressure** | 185 bar | 180–190 bar | **185.2 bar** | | **Pressure Stability** | ±2 bar | ±3 bar max | **±1.5 bar** | | **Relief Valve Operation** | 0% duty cycle | < 1% | **0%** | | **Wasted Power (Relief)** | 0 MW | < 1 MW | **0 MW** | | **VFD Frequency** @ 175 bar steam | 49–50 Hz | 48–51 Hz | **49.3 Hz** | | **Motor Current** @ full load | 380–400 A | < 450 A | **392 A** | | **Discharge Temperature Rise** | 8–12°C | < 15°C | **10.8°C** | | **Suction Pressure Margin** | > 0.3 bar | > 0.2 bar | **0.38 bar** | ### Transient Response **Load Step: 25% → 100% (Turbine throttle open rapidly)** | Time (sec) | Load (%) | P_discharge (bar) | VFD (Hz) | Relief Open | |-----------|----------|-----------------|----------|-------------| | 0 | 25 | 170 | 40 | No | | 5 | 45 | 172 | 43 | No | | 10 | 65 | 178 | 46 | No | | 15 | 85 | 188 | 48 | Yes! (1.2 kg/s) | | 20 | 100 | 187 | 49 | Yes (0.8 kg/s) | | 30 | 100 | 185 | 49.3 | No ✓ | | 60 | 100 | 185 | 49.3 | No (steady) | **Notes:** - Small overshoot to 188 bar at t=15 sec (acceptable, relief cracks to bleed excess) - PID corrects back to 185 bar within 30 seconds - No hunting; smooth convergence --- ## 🔄 Advanced Variations ### Variation A: Cascade Pressure Control (Multi-Stage Pump) For very high discharge pressures (>250 bar) or large plants (>500 MW): - **Master (Outer) Loop:** Final discharge pressure (185 bar target) - **Slave (Inner) Loop:** Intermediate pump stage pressure (to prevent cavitation in later stages) Both loops feed the same VFD command (master dominant). ### Variation B: Duty Cycling (Fixed-Speed Pump + Proportional Bypass) Alternative to VFD: - Pump runs fixed at 1500 RPM (50% speed) = ~90 bar head - Proportional bypass valve modulates: open more = relief flow ↑ - Simpler control, but ~5–8% continuous energy loss Loop would use proportional valve position instead of VFD frequency. ### Variation C: Load-Following Setpoint Scheduling For power plants following grid demand: - **Off-peak (night):** Setpoint 175 bar (reserve capacity) - **Peak hours:** Setpoint 185 bar (maximum efficiency) - Smooth ramp over 5 minutes (avoid transient shock) --- ## 📄 Document Version History | Version | Date | Author | Change | |---------|------|--------|--------| | 1.0 | 2026-04-13 | Claude | Initial template: VFD speed PID + relief monitoring | --- *This template is part of the TSIMEREZIVO Industrial Process Control Library.*

More like this

Rate, comment, and get full access

Members can download files, rate contributions, and discuss fixes with the engineers who posted them — free.

Join the library