Field fix / guideDesign DocumentVendor-agnostic (IEC 61131-3)Power Plantindustrial-automation

Turbine Inlet (Main Steam) Pressure Regulator — Control Design

Shared by TSIMEREZIVO Team · 4 Oct 2026 · 45 views

# TSIMEREZIVO Template: Turbine Inlet (Main Steam) Pressure Regulator **Category:** Power Plant | **Industry:** Thermal Power Generation | **Language:** Ladder / Structured Text --- ## 📋 Overview ### Purpose Regulate main steam pressure at the turbine inlet to exactly 175 bar (design point) to balance competing demands: - **If P < 175 bar:** Turbine loses power (low enthalpy drop = low electrical output) - **If P > 175 bar:** Boiler relief valve opens, wastes steam (loss of thermal efficiency) - **If P oscillates:** Cause swell/shrink in boiler drum (upsets level control) This is the **second-most critical control** in the plant (after turbine speed governor). ### Typical Application - **Plant:** 100–300 MWe steam power station - **Design Pressure:** 175 bar at throttle - **Design Temperature:** 540°C superheated steam - **Control Element:** Proportional regulating valve (or VFD-driven turbine inlet valve) - **Monitoring:** Differential pressure across regulator, upstream/downstream pressure ### Critical Balance Main steam pressure is bridged between two systems: - **Upstream:** Boiler (creates steam at ~185 bar with buffer capacity) - **Downstream:** Turbine (accepts steam at ~175 bar; demand varies with load) - **Regulator Job:** Drop the .bar-equivalent pressure from boiler (185) to turbine (175) while maintaining steady flow = constant electrical load --- ## 🎯 Control Philosophy ### Key Equations **Pressure Drop Across Regulator (Proportional Control Valve):** ``` ΔP_regulator [bar] = P_boiler − P_turbine_inlet = 185 − 175 = 10 bar nominal For proportional valve: ΔP ∝ (Valve Opening %)² (orifice flow law) Critical flow path: If valve opens 50% and ΔP = 10 bar → Find opening that maintains ΔP in proportional relationship ``` **Governing Requirement:** ``` For isobaric control (constant pressure): Valve position = f(error) [proportional] For droop control (pressure follows load): Pressure setpoint = 175 − 0.5 × (Load %) [compensation] → At full load: SP = 175 − 5 = 170 bar (deliberate sag to share load among units) ``` **Speed of Response (PID Tuning):** ``` Kp = proportional gain = 0.3 (moderate; system has thermal lag) Ki = integral gain = 0.01 (slow; prevent relief valve hunting) Kd = derivative gain = 0 (not used; causes oscillation with proportional valve) Scan rate: 1 second (fast enough for steam dynamics) ``` ### Control Strategy: **Two Modes** ``` MODE 1: ISOCHRONOUS (Standalone/Island Plant) Fixed 175 bar at throttle Turbine frequency = 60 Hz locked Regulator adjusts to match demand If load ↑ → valve opens more → pressure steady at 175 ✓ If load ↓ → valve closes more → pressure steady at 175 ✓ MODE 2: DROOP (Grid-Connected, Load-Sharing) Pressure intentionally sags with load (5% droop typical) Allows parallel turbines to share load equally If load ↑ → turbine speed sensor drops slightly → Governor allows throttle more open → more steam → pressure maintained → Load sharing automatic Example: At 50% load: P = 175 − (0.5 × (50%)) = 175 − 25 = 150 bar? No! Droop is 5% of design pressure: 175 − (0.05 × 175) = 166 bar @ full load ``` --- ## 🏗️ Control Logic ### Pseudocode: Main Steam Pressure Regulator (Isobaric, Single-Unit Standalone) ```pascal PROGRAM TurbineInletPressureRegulator; { ========== DECLARATIONS ========== } VAR -- INPUT SENSORS turbine_inlet_pressure : REAL; { 0-250 bar, absolute pressure before throttle } turbine_outlet_pressure : REAL; { Back-pressure; used for differential P monitoring } boiler_main_steam_press : REAL; { 150-250 bar, upstream of regulator } regulator_valve_position : REAL; { 0-100 %, spool feedback } steam_flow_through_valve : REAL; { 0-300 kg/s, orifice flowmeter } turbine_speed_rpm : REAL; { 0-3600 RPM, for load indication } turbine_power_mw : REAL; { 0-300 MW, electrical load } -- CONTROL SETPOINTS pressure_sp : REAL := 175.0; { Isobaric setpoint } pressure_alarm_high : REAL := 185.0; { Approaching relief valve } pressure_trip_high : REAL := 195.0; { Relief stuck open? } pressure_alarm_low : REAL := 160.0; { Under-pressure } pressure_trip_low : REAL := 150.0; { Critical low } -- CONTROL LOOP pressure_error : REAL; pid_integral_term : REAL := 0.0; pressure_prev : REAL := 175.0; -- PROPORTIONAL PID TUNING kp_main_steam : REAL := 0.30; { Proportional gain } ki_main_steam : REAL := 0.010; { Very slow integral } kd_main_steam : REAL := 0.0; { NO derivative } integral_limit_hi : REAL := 0.25; { Limit integral output } integral_limit_lo : REAL := -0.15; scan_time : REAL := 1.0; -- VALVE COMMAND valve_command_raw : REAL; valve_command_limited : REAL; valve_rate_limit : REAL := 2.0; { %/sec slew rate } valve_command_prev : REAL := 50.0; -- PRESSURE DROP MONITORING (Valve Health) differential_pressure : REAL; dp_expected_at_position : REAL; valve_flow_capacity_at_op : REAL; -- LOAD INDICATION load_percent : REAL; load_change_rate : REAL; -- DROOP MODE (Optional) droop_mode_active : BOOL := FALSE; { Set to TRUE for grid-connected } droop_percent : REAL := 5.0; { 5% droop standard } pressure_sp_with_droop : REAL; -- OUTPUT COMMANDS regulator_valve_command : REAL; { 0-100 % command signal } BEGIN { ========== SELECT SETPOINT MODE ========== } IF droop_mode_active THEN { Grid-connected: Pressure sags with load to share among parallel turbines } load_percent := turbine_power_mw / 300.0 × 100.0; { Assume 300 MW nominal plant } pressure_sp_with_droop := 175.0 − (droop_percent / 100.0 × 175.0 × (load_percent / 100.0)); { Example: 50% load = 150 MW SP = 175 − (0.05 × 175 × 0.50) = 175 − 4.375 = 170.625 bar At full load: SP = 175 − (0.05 × 175 × 1.0) = 166.25 bar } pressure_sp := pressure_sp_with_droop; ELSE { Isobaric (this version) } pressure_sp := 175.0; { Fixed } END_IF; { ========== ERROR CALCULATION ========== } pressure_error := pressure_sp − turbine_inlet_pressure; { ========== PROPORTIONAL TERM ========== } proportional_term := kp_main_steam × pressure_error; { ========== INTEGRAL TERM (Slow) ========== } pid_integral_term := pid_integral_term + (ki_main_steam × pressure_error × scan_time); -- Anti-windup IF pid_integral_term > integral_limit_hi THEN pid_integral_term := integral_limit_hi; ELSIF pid_integral_term < integral_limit_lo THEN pid_integral_term := integral_limit_lo; END_IF; { ========== COMBINED COMMAND ========== } valve_command_raw := 50.0 + proportional_term + pid_integral_term; { ========== RATE LIMITING ========== } valve_delta := valve_command_raw − valve_command_prev; max_delta := valve_rate_limit × scan_time; IF valve_delta > max_delta THEN valve_command_limited := valve_command_prev + max_delta; ELSIF valve_delta < -max_delta THEN valve_command_limited := valve_command_prev − max_delta; ELSE valve_command_limited := valve_command_raw; END_IF; { ========== OUTPUT LIMITS ========== } IF valve_command_limited < 0.0 THEN regulator_valve_command := 0.0; ELSIF valve_command_limited > 100.0 THEN regulator_valve_command := 100.0; ELSE regulator_valve_command := valve_command_limited; END_IF; { ========== VALVE HEALTH MONITORING ========== } differential_pressure := boiler_main_steam_press − turbine_inlet_pressure; -- For proportional valve: expect ΔP ∝ Position%² -- At 50% open: expect ~% of design ΔP -- At 100% open: expect minimal ΔP -- Rough estimate: ΔP_expected = 20 bar × (0.5 × (1 − Position%)) -- At 50% position: ΔP = 20 × 0.5 = 10 bar (matches typical) dp_expected_at_position := 20.0 × (1.0 − (regulator_valve_command / 100.0)) × 0.5; -- If actual ΔP >> expected ΔP → valve cartridge buildup/erosion IF differential_pressure > (dp_expected_at_position + 5.0) THEN { WARN: "Regulator valve ΔP high — possible cartridge buildup or erosion" } END_IF; -- If actual ΔP << expected ΔP → valve not following command (stuck) IF differential_pressure < (dp_expected_at_position − 5.0) AND regulator_valve_command > 50.0 THEN { WARN: "Regulator valve suspected stuck — not opening properly" } END_IF; { ========== ALARMS ========== } IF turbine_inlet_pressure > pressure_alarm_high THEN { WARN: "Main steam pressure high — approaching boiler relief valve" } END_IF; IF turbine_inlet_pressure > pressure_trip_high THEN { CRITICAL: "Main steam pressure CRITICAL — boiler relief stuck? Or regulator stuck closed?" } END_IF; IF turbine_inlet_pressure < pressure_alarm_low THEN { WARN: "Main steam pressure low — turbine output decreasing" } END_IF; IF turbine_inlet_pressure < pressure_trip_low THEN { CRIT: "Main steam pressure critical low — turbine cannot sustain rated load" } END_IF; -- Check if regulator at limit while pressure wrong IF regulator_valve_command >= 99.0 AND turbine_inlet_pressure < 170.0 THEN { ALARM: "Regulator saturated (fully open) but pressure still falling — upstream supply issue" } END_IF; IF regulator_valve_command <= 1.0 AND turbine_inlet_pressure > 185.0 THEN { ALARM: "Regulator saturated (fully closed) but pressure still high — boiler overpressure" } END_IF; { ========== UPDATE STATE FOR NEXT CYCLE ========== } pressure_prev := turbine_inlet_pressure; valve_command_prev := valve_command_limited; { ========== SEND COMMAND ========== } -- Output: regulator_valve_command (0-100 % proportional control signal) END_PROGRAM; ``` --- ## 🏷️ Tag List | Tag Name | Type | Range | Units | Description | |----------|------|-------|-------|-------------| | `TURBINE_INLET_PRESSURE` | AI | 100–200 | bar | Main steam throttle pressure (critical) | | `BOILER_MAIN_STEAM_PRESS` | AI | 170–195 | bar | Upstream of regulator | | `REGULATOR_VALVE_FEEDBACK` | AI | 0–100 | % | Spool position (for valve diagnostics) | | `STEAM_FLOW_MAIN` | AI | 0–300 | kg/s | Through turbine throttle | | `TURBINE_SPEED` | AI | 0–3600 | RPM | For load indication | | `TURBINE_POWER_MW` | AI | 0–300 | MW | Electrical load | --- ## 🚨 Alarm & Trip Matrix | Condition | Threshold | Severity | Action | Recovery | |-----------|-----------|----------|--------|----------| | **Pressure High** | > 185 bar | ⚠️ WARN | Close valve more; boiler relief opening | < 180 bar | | **Pressure Critical** | > 195 bar | 🔴 TRIP | Regulator stuck closed OR boiler overfiring | Regulator inspection | | **Pressure Low** | < 160 bar | ⚠️ WARN | Open valve more; check boiler supply | > 165 bar | | **Pressure Critical** | < 150 bar | 🔴 TRIP | Turbine cannot deliver rated power | Boiler/Steam line check | | **Regulator Stuck** | Cmd ≠ Fdbk >10 sec | ⚠️ WARN | Valve cartridge dirty or spool jam | Manual override; valve cleaning | --- ## 📺 HMI Layout ### Main Steam Pressure Regulator Control Panel ``` ┌────────────────────────────────────────────────┐ │ TURBINE INLET (MAIN STEAM) PRESSURE CTRL │ ├────────────────────────────────────────────────┤ │ │ │ Inlet Pressure: 175.2 bar ✓ [SP: 175.0] │ │ Upstream (Boiler): 185.5 bar (ΔP: 10.3 bar)│ │ Flow: 195 kg/s │ │ │ │ Regulator Valve: ████████░░ 48% │ │ Command: ████████░░ 48% (sync ✓) │ │ Spool Position: ████████░░ 48% (feedback)│ │ │ │ Turbine Load: 75% (225 MW) │ │ Mode: ISOBARIC (Fixed 175 bar) │ │ │ │ ╔═══════════════════════════════════════╗ │ │ ║ Control Status: ║ │ │ ║ ✓ Pressure Stable ±0.5 bar ║ │ │ ║ ✓ Valve Responding (sync with cmd) ║ │ │ ║ ✓ Upstream Supply Adequate (185 bar) ║ │ │ ║ ✓ No Relief Valve Opening ║ │ │ ╚═══════════════════════════════════════╝ │ │ │ │ [Load: 75%] [SP Type: Fixed] [Monitor] │ │ │ └────────────────────────────────────────────────┘ ``` --- ## 📊 Expected Performance (Isobaric Mode) | Parameter | Target | Range | Typical | |-----------|--------|-------|---------| | **Inlet Pressure** | 175.0 bar | 173–177 bar | **175.2 bar** | | **Stability** | ±0.5 bar | ±1.0 bar max | **±0.4 bar** | | **Valve Position** | 48–52% @ mid-load | 0–100% operating | **48%** | | **Response Time** | < 10 sec | < 20 sec max | **6 sec** | --- ## 🔄 Advanced Variations ### Variation A: Droop Mode (Grid-Connected Load-Sharing) For plants in parallel electrical grid: pressure setpoint sags 5% from no-load to full-load. Allows automatic load sharing among turbine units. ### Variation B: Sliding Pressure Operation For maximum efficiency: Allow boiler pressure to vary with load (90–185 bar range). Regulator maintains throttle at optimal superheat. --- ## 📄 Document Version History | Version | Date | Author | Change | |---------|------|--------|--------| | 1.0 | 2026-04-13 | Claude | Initial template: Isobaric pressure control | --- *This template is part of the TSIMEREZIVO Industrial Process Control Library.*

More like this

Rate, comment, and get full access

Members can download files, rate contributions, and discuss fixes with the engineers who posted them — free.

Join the library