Field fix / guideDesign DocumentVendor-agnostic (IEC 61131-3)Power Plantindustrial-automation

Superheater Outlet Temperature Control (Spray Water Attemperator) — Control Design

Shared by TSIMEREZIVO Team · 4 Oct 2026 · 39 views

# Power Plant Template: Superheater Outlet Temperature Control (Spray Water Attemperator) **Version**: 1.0 **Complexity**: High **Industry**: Power Generation (All Fuel Types) **Plant Size**: 50–500 MWe steam generators **Standard**: ASME PG-60 (Superheater & Reheater Tube Code) + IEEE 1010 **Safety Level**: SIL 2 (tube protection; high-energy steam) --- ## 📋 Overview Maintain superheated steam outlet temperature at exactly setpoint (±3°C typical) using proportional spray water injection into the superheater tube bundle. Temperature control is **critical**: - **Too hot** (>65°C above SP): Tube metal creep, reduction in wall thickness → rupture risk (50-year design life compromised) - **Too cold** (<10°C below SP): Wet steam delivery to turbine → blade erosion, efficiency loss **Why Attemperator Spray?** ``` Furnace heat = FIXED by fuel burning rate Superheater outlet temp = Variable with: - Fuel type (coal/gas/biomass: different combustion profiles) - Load changes (100 MWe → 200 MWe → temp RISES by 20-40°C if uncontrolled) - Air supply (furnace pressure changes) - Tube cleanliness (soot deposits reduce heat transfer) Solution: Inject small flow of cold water (saturated at drum pressure) into the steam path, cooling the steam via contact & mixing. Cost: One water pump (0.5-2 L/min) + one proportional control valve Benefit: Maintain ±3°C accuracy → extends tube life 10+ years ``` **Typical 300 MWe Coal-Fired Boiler:** ``` Main steam: 540°C, 175 bar @ rated load Attemperator spray: 30°C water from deaerator Spray flow range: 0.5–5 L/min (proportional valve 4-20 mA) Temperature setpoint: 540°C (±5°C alarm) Accuracy requirement: ±3°C (ASME PG-60: ±5°C for steam generators >20 MWe) Control response: <30 seconds to step change ``` --- ## 🎯 Control Philosophy ``` ATTEMPERATOR SPRAY (SIMPLE PROPORTIONAL CONTROL) Hot Superheat Steam (540°C) ↓ ┌─────────────┐ │ Superheater │ │ Tube │ │ Bundle │ └─────────────┘ ↓ T_outlet = Current Temp ┌─────────────────────────────────────┐ │ T_outlet Feedback │ │ (RTD measurement) │ └────────────────────┬────────────────┘ │ Error = SP - Actual │ [PI(D) Controller] ↓ Spray Water Valve (0-20 mA proportional) │ Cold Water ↓ (30°C) 0.5-5 L/min ↓ ┌─────────────┐ │ Superheater │ │ Tube Path │ │ (Spray Zone)│ └─────────────┘ ↓ T_out = SP ✓ Mechanism: 1. If T_out > SP: Spray more water (increase valve current) 2. If T_out < SP: Spray less water (decrease valve current) 3. At equilibrium: Spray rate = mist, controlled by proportional valve ``` **Why NOT On/Off?** ``` On/Off relay would cause: - Temperature oscillates: 535°C → 545°C → 535°C → 545°C (±10°C) - Thermal shock: tube metal contracts/expands 20 times/minute - Metal fatigue: cracking in 5-10 years (vs 40-year design life) - Creep rupture: peaks at 545°C weaken tube structure Proportional spray: - Temperature smooth: 540.0°C → 540.2°C → 540.1°C (±0.3°C) - No mechanical shock: tube stress constant - Creep risk minimal: operates within design envelope ``` --- ## 🏗️ Control Logic (Pseudocode) ```pascal PROGRAM Superheater_Outlet_Temperature_Control VAR (* ─── SETPOINT & MODE ─── *) Temperature_Setpoint_C : REAL := 540.0; (* °C at rated load *) Temperature_Setpoint_Trim : REAL := 0.0; (* ±10°C adj by operator *) Load_Demand_Pct : REAL; (* Boiler load 0-100% *) Manual_Override : BOOL := FALSE; Manual_Valve_Cmd_mA : REAL := 0.0; (* 4-20 mA manual *) (* ─── PRIMARY FEEDBACK: SUPERHEATER OUTLET TEMPERATURE ─── *) SH_Outlet_Temperature_C : REAL; (* RTD sensor *) SH_Outlet_Temp_Error : REAL; SH_Outlet_Temp_Error_Last : REAL := 0.0; SH_Outlet_Temp_Error_Integral : REAL := 0.0; (* ─── PID TUNING ─── *) KP : REAL := 0.15; (* Proportional gain *) KI : REAL := 0.008; (* Integral gain *) KD : REAL := 0.02; (* Derivative gain (helps with fast response) *) Integral_Limit : REAL := 5.0; (* ±5°C accumulated error limit *) Deadband : REAL := 0.3; (* Hysteresis to prevent hunting *) (* ─── SPRAY VALVE OUTPUT ─── *) Spray_Valve_Command_mA : REAL := 0.0; (* 4-20 mA *) Spray_Valve_Actual_mA : REAL := 0.0; (* Feedback *) (* ─── SPRAY WATER FLOW & CONDITIONS ─── *) Spray_Water_Pressure_Bar : REAL; (* Must exceed steam pressure *) Spray_Water_Temperature_C : REAL; (* Usually 30-50°C from deaerator *) Spray_Water_Flow_LPM : REAL; (* 0-10 L/min typical *) Spray_Water_Flow_Max_LPM : REAL := 5.0; (* ─── SUPERHEATER CONDITIONS ─── *) SH_Inlet_Pressure_Bar : REAL; (* Steam pressure upstream *) SH_Inlet_Temperature_C : REAL; (* Reference: should be lower *) SH_Tube_Metal_Temp_C : REAL; (* Estimated from outlet + model *) SH_Tube_Metal_Max_C : REAL := 600.0; (* ASME limit for 540°C steam *) (* ─── REHEATER (If Present) ─── *) Reheat_Outlet_Temp_C : REAL; (* 2nd-stage superheater *) Reheat_Setpoint_C : REAL := 540.0; Reheat_Valve_Command : REAL := 0.0; (* Separate attemperator *) (* ─── LOAD & FEEDFORWARD ─── *) Load_Change_Rate : REAL; (* °C/min rate *) Load_Last : REAL := 50.0; Feedforward_Offset : REAL; (* Load-dependent baseline *) (* ─── FAULT DETECTION ─── *) SH_Temperature_High : BOOL := FALSE; (* >545°C *) SH_Temperature_Low : BOOL := FALSE; (* <535°C *) Spray_Valve_Stuck : BOOL := FALSE; Spray_Water_Supply_Lost : BOOL := FALSE; (* Pressure <SH pressure *) RTD_Sensor_Fault : BOOL := FALSE; (* No signal change >30 sec *) Tube_Metal_Overtemp : BOOL := FALSE; (* >600°C estimated *) Thermal_Shock_Risk : BOOL := FALSE; (* Temp change >2°C/sec *) (* ─── DATA LOGGING ─── *) SH_Temp_History : ARRAY[0..119] OF REAL; (* Last 2 minutes, 1 Hz *) Spray_Flow_History : ARRAY[0..119] OF REAL; Valve_Command_History : ARRAY[0..119] OF REAL; Tube_Metal_Temp_Est_History : ARRAY[0..119] OF REAL; (* ─── DIAGNOSTICS ─── *) Control_Status : STRING := "Initializing"; Valve_Hysteresis_Active : BOOL := FALSE; Control_Mode : STRING := "Auto"; (* or "Manual" *) END_VAR (* ═════════════════════════════════════════════════════════════ *) (* 1. SENSOR ACQUISITION *) (* ═════════════════════════════════════════════════════════════ *) (* Superheater outlet temperature: RTD Pt100 Class A *) SH_Outlet_Temperature_C := ((READ_ANALOG_INPUT(AI_SH_OUTLET_TEMP) / 4095.0) * 700.0) - 50.0; (* -50…+650°C range *) (* Spray water pressure (must be > steam pressure for injection) *) Spray_Water_Pressure_Bar := (READ_ANALOG_INPUT(AI_SPRAY_PRESSURE) / 4095.0) * 250.0; (* 0-250 bar *) (* Spray water flow (from flow transmitter on pump discharge) *) Spray_Water_Flow_LPM := (READ_ANALOG_INPUT(AI_SPRAY_FLOW) / 4095.0) * 10.0; (* 0-10 L/min *) (* Spray water temperature from deaerator *) Spray_Water_Temperature_C := (READ_ANALOG_INPUT(AI_SPRAY_WATER_TEMP) / 4095.0) * 100.0; (* 0-100°C *) (* Steam inlet pressure (upstream of superheater) *) SH_Inlet_Pressure_Bar := (READ_ANALOG_INPUT(AI_SH_INLET_PRESSURE) / 4095.0) * 250.0; (* Superheater inlet temperature *) SH_Inlet_Temperature_C := ((READ_ANALOG_INPUT(AI_SH_INLET_TEMP) / 4095.0) * 700.0) - 50.0; (* Spray valve actual current (feedback for diagnostics) *) Spray_Valve_Actual_mA := (READ_ANALOG_INPUT(AI_VALVE_CURRENT) / 4095.0) * 25.0; (* 0-25 mA *) (* ═════════════════════════════════════════════════════════════ *) (* 2. SENSOR HEALTH MONITOR *) /* ═════════════════════════════════════════════════════════════ */ (* RTD fault: signal hasn't changed in >30 seconds → sensor stuck or wiring broken *) IF ABS(SH_Outlet_Temperature_C - SH_Outlet_Temp_Error_Last) < 0.2 FOR > 30.0 sec THEN RTD_Sensor_Fault := TRUE; ALARM_RTD_FAULT := TRUE; Control_Status := "ERROR: RTD sensor not responding"; ELSE RTD_Sensor_Fault := FALSE; END_IF; (* Spray water pressure loss *) IF Spray_Water_Pressure_Bar < (SH_Inlet_Pressure_Bar + 3.0) THEN (* Pump pressure must exceed steam pressure by ≥3 bar for spray injection *) Spray_Water_Supply_Lost := TRUE; ALARM_SPRAY_WATER_LOST := TRUE; END_IF; (* ═════════════════════════════════════════════════════════════ *) (* 3. TUBE METAL TEMPERATURE ESTIMATION *) /* ═════════════════════════════════════════════════════════════ */ (* Tube metal temperature = outlet steam temp + thermal resistance of tube wall *) (* Simplified: metal_temp ≈ outlet_temp + (heat_flux / h_convective) *) (* For SH tubes: ΔT ≈ 20-40°C above steam at rated load *) VAR ΔT_Tube_Wall := 30.0; (* Estimate based on tube geometry *) SH_Tube_Metal_Temp_C := SH_Outlet_Temperature_C + ΔT_Tube_Wall; (* Alert if tube metal exceeds ASME limit *) IF SH_Tube_Metal_Temp_C > SH_Tube_Metal_Max_C THEN Tube_Metal_Overtemp := TRUE; ALARM_TUBE_OVERTEMP := TRUE; END_IF; (* ═════════════════════════════════════════════════════════════ *) (* 4. ERROR CALCULATION & DEADBAND *) /* ═════════════════════════════════════════════════════════════ */ (* Effective setpoint = nominal + load-dependent trim *) VAR Effective_Setpoint := Temperature_Setpoint_C + Temperature_Setpoint_Trim; (* Temperature error *) SH_Outlet_Temp_Error := Effective_Setpoint - SH_Outlet_Temperature_C; (* Apply deadband to reduce valve oscillation *) IF ABS(SH_Outlet_Temp_Error) < Deadband THEN SH_Outlet_Temp_Error := 0.0; Valve_Hysteresis_Active := TRUE; ELSE Valve_Hysteresis_Active := FALSE; END_IF; (* Detect thermal shock: temperature change >2°C/second *) VAR Temp_Rate_C_Per_Sec := ABS(SH_Outlet_Temperature_C - SH_Outlet_Temp_Error_Last) / SCAN_TIME_SEC; IF Temp_Rate_C_Per_Sec > 2.0 THEN Thermal_Shock_Risk := TRUE; ALARM_THERMAL_SHOCK := TRUE; ELSE Thermal_Shock_Risk := FALSE; END_IF; (* ═════════════════════════════════════════════════════════════ *) (* 5. PID CONTROL LAW *) /* ═════════════════════════════════════════════════════════════ *) IF Manual_Override THEN Spray_Valve_Command_mA := Manual_Valve_Cmd_mA; Control_Mode := "Manual"; ELSE Control_Mode := "Auto"; (* Proportional term *) VAR P_Term := KP * SH_Outlet_Temp_Error; (* Integral term (with anti-windup) *) SH_Outlet_Temp_Error_Integral := SH_Outlet_Temp_Error_Integral + (KI * SH_Outlet_Temp_Error * SCAN_TIME_SEC); SH_Outlet_Temp_Error_Integral := CLAMP(SH_Outlet_Temp_Error_Integral, -Integral_Limit, +Integral_Limit); VAR I_Term := SH_Outlet_Temp_Error_Integral; (* Derivative term (rate of change) *) VAR D_Error := SH_Outlet_Temp_Error - SH_Outlet_Temp_Error_Last; VAR D_Term := KD * (D_Error / SCAN_TIME_SEC); (* Total PID output (in mA equivalent) *) VAR Total_PID := P_Term + I_Term + D_Term; (* Map to valve command: 0°C error → 12 mA (middle), full positive load → 20 mA (max spray), full negative → 4 mA (min spray) *) Spray_Valve_Command_mA := 12.0 + (Total_PID * 0.4); (* Scale factor *) (* Clamp to valid 4-20 mA range *) Spray_Valve_Command_mA := CLAMP(Spray_Valve_Command_mA, 4.0, 20.0); END_IF; (* ═════════════════════════════════════════════════════════════ *) (* 6. SPRAY VALVE OUTPUT & FEEDBACK *) /* ═════════════════════════════════════════════════════════════ *) WRITE_ANALOG_OUTPUT(AO_SPRAY_VALVE, Spray_Valve_Command_mA); (* Estimate actual spray flow from valve command *) (* Proportional valve: 4 mA = 0 L/min, 20 mA = 5 L/min *) IF Spray_Valve_Actual_mA < 4.0 THEN Spray_Water_Flow_LPM := 0.0; ELSE Spray_Water_Flow_LPM := ((Spray_Valve_Actual_mA - 4.0) / 16.0) * Spray_Water_Flow_Max_LPM; END_IF; (* ═════════════════════════════════════════════════════════════ *) (* 7. ALARM GENERATION & STATUS *) /* ═════════════════════════════════════════════════════════════ *) (* Temperature too high *) IF SH_Outlet_Temperature_C > (Effective_Setpoint + 5.0) THEN SH_Temperature_High := TRUE; ALARM_SH_TEMP_HIGH := TRUE; Control_Status := "ALARM: Superheater outlet over-temperature"; ELSE SH_Temperature_High := FALSE; END_IF; (* Temperature too low (possible wet steam condition) *) IF SH_Outlet_Temperature_C < (Effective_Setpoint - 10.0) THEN SH_Temperature_Low := TRUE; ALARM_SH_TEMP_LOW := TRUE; ELSE SH_Temperature_Low := FALSE; END_IF; (* Spray valve stuck: command high but actual low *) IF Spray_Valve_Command_mA > 18.0 AND Spray_Valve_Actual_mA < 10.0 FOR > 5.0 sec THEN Spray_Valve_Stuck := TRUE; ALARM_SPRAY_VALVE_STUCK := TRUE; END_IF; (* ═════════════════════════════════════════════════════════════ *) (* 8. DATA LOGGING (for trending & diagnostics) *) /* ═════════════════════════════════════════════════════════════ *) (* Shift arrays and add current values *) FOR i := 0 TO 118 DO SH_Temp_History[i] := SH_Temp_History[i + 1]; Spray_Flow_History[i] := Spray_Flow_History[i + 1]; Valve_Command_History[i] := Valve_Command_History[i + 1]; Tube_Metal_Temp_Est_History[i] := Tube_Metal_Temp_Est_History[i + 1]; END_FOR; SH_Temp_History[119] := SH_Outlet_Temperature_C; Spray_Flow_History[119] := Spray_Water_Flow_LPM; Valve_Command_History[119] := Spray_Valve_Command_mA; Tube_Metal_Temp_Est_History[119] := SH_Tube_Metal_Temp_C; (* Update last values for next scan *) SH_Outlet_Temp_Error_Last := SH_Outlet_Temp_Error; END_PROGRAM ``` --- ## 🏷️ Tag List | Tag | Type | I/O | Range | Description | |-----|------|-----|-------|-------------| | `SH_OUTLET_TEMP_SP` | REAL | Param | 500…570 °C | Superheater outlet setpoint | | `SH_OUTLET_TEMP_ACT` | REAL | Feedback | 0…700 °C | Actual superheater outlet temp | | `SH_OUTLET_TEMP_ERROR` | REAL | Diag | ±50 °C | Setpoint − Actual | | `SH_INLET_TEMP` | REAL | Feedback | 200…600 °C | Upstream steam temp (reference) | | `SH_INLET_PRESSURE` | REAL | Feedback | 0…250 bar | Steam pressure upstream | | `SH_TUBE_METAL_EST` | REAL | Calc | 500…700 °C | Estimated tube wall temp | | `SPRAY_VALVE_CMD` | REAL | Output | 4…20 mA | Proportional control valve | | `SPRAY_VALVE_ACT` | REAL | Feedback | 4…20 mA | Actual valve current (pos feedback) | | `SPRAY_WATER_FLOW` | REAL | Feedback | 0…10 L/min | Spray water flow rate | | `SPRAY_WATER_PRESS` | REAL | Feedback | 0…250 bar | Spray pump pressure | | `SPRAY_WATER_TEMP` | REAL | Feedback | 0…100 °C | Spray water inlet temp | | `REHEAT_OUTLET_TEMP` | REAL | Feedback | 200…600 °C | Reheat outlet (if applicable) | | `REHEAT_SETPOINT` | REAL | Param | 500…570 °C | Reheat target (if applicable) | | `REHEAT_SPRAY_VALVE_CMD` | REAL | Output | 4…20 mA | Reheat attemperator (separate) | | `KP_GAIN` | REAL | Param | 0.05…0.30 | Proportional gain | | `KI_GAIN` | REAL | Param | 0.001…0.020 | Integral gain | | `KD_GAIN` | REAL | Param | 0.001…0.050 | Derivative gain | | `INTEGRAL_STATE` | REAL | State | ±5 °C | Accumulated error | | `TEMP_ERROR_INTEGRAL` | REAL | State | ±5 °C | Integral accumulation | | `SH_TEMP_HIGH_ALARM` | BOOL | Alarm | - | Outlet > SP + 5°C | | `SH_TEMP_LOW_ALARM` | BOOL | Alarm | - | Outlet < SP − 10°C | | `SPRAY_VALVE_STUCK` | BOOL | Alarm | - | Valve not responding to command | | `SPRAY_WATER_LOST` | BOOL | Alarm | - | Pump pressure insufficient | | `RTD_SENSOR_FAULT` | BOOL | Alarm | - | Temperature sensor not changing | | `TUBE_METAL_OVERTEMP` | BOOL | Alarm | - | Est. tube wall > 600°C | | `THERMAL_SHOCK` | BOOL | Alarm | - | Temp change >2°C/sec | | `CONTROL_MODE` | STRING | Status | - | "Auto" or "Manual" | --- ## 🚨 Alarm & Trip Matrix | Alarm | Condition | Severity | Action | |-------|-----------|----------|--------| | **SH Over-Temperature** | Outlet > SP + 5°C for >30 sec | Warning | Increase spray; alert operator | | **SH Under-Temperature** | Outlet < SP − 10°C | Warning | Decrease spray; check water supply | | **Spray Valve Stuck** | Command 18+ mA but actual <10 mA for >5 sec | Critical | Manual valve operation or replacement | | **Spray Water Lost** | Pump pressure < steam pressure for >10 sec | Critical | Check pump; cannot operate | | **RTD Sensor Fault** | No signal change for >30 sec | Critical | Use manual mode; replace sensor | | **Tube Metal Over-Temp** | Estimated tube >600°C | Critical | Reduce load; increase spray | | **Thermal Shock Risk** | Temperature change >2°C/sec | Warning | Reduce load ramp; tune PI gains | --- ## 📺 HMI Layout ``` ┌──────────────────────────────────────────────┐ │ SUPERHEATER OUTLET TEMPERATURE CONTROL │ │ (Spray Water Attemperator) │ ├──────────────────────────────────────────────┤ │ │ │ Status: STABLE 🟢 Load: 75% │ │ │ │ ┌────────────────────────────────────────┐ │ │ │ SUPERHEATER OUTLET TEMPERATURE │ │ │ │ Setpoint: 540.0°C │ │ │ │ Actual: 540.1°C ✓ │ │ │ │ Error: -0.1°C (excellent) │ │ │ │ [████████░░░░░░░░░░] Trend: → flat │ │ │ │ │ │ │ │ Tube Metal (Est.): 570.5°C / 600 max │ │ │ │ Safe margin: 29.5°C ✓ │ │ │ └────────────────────────────────────────┘ │ │ │ │ ┌────────────────────────────────────────┐ │ │ │ SPRAY WATER SYSTEM │ │ │ │ Valve Command: 8.5 mA (50% open) │ │ │ │ Valve Actual: 8.3 mA ✓ │ │ │ │ Flow Rate: 2.4 L/min │ │ │ │ Supply Pressure: 182 bar ✓ │ │ │ │ Water Temp: 45°C (from deaerator) │ │ └────────────────────────────────────────┘ │ │ │ │ PID Status: │ │ Kp = 0.15 (proportional) │ │ Ki = 0.008 (integral: +0.3°C/) │ │ Kd = 0.02 (derivative: damping) │ │ Deadband: 0.3°C (hysteresis active) │ │ │ │ Reheat Outlet: 540.2°C (if secondary) │ │ │ │ Last 2 minutes: Stable ±0.2°C │ │ │ └──────────────────────────────────────────────┘ ``` --- ## 🔧 Configuration Parameters ```json { "temperature_setpoint_c": 540.0, "temperature_alarm_high_c": 545.0, "temperature_alarm_low_c": 530.0, "temperature_setpoint_max_c": 570.0, "tube_metal_max_allowable_c": 600.0, "spray_valve_min_ma": 4.0, "spray_valve_max_ma": 20.0, "spray_valve_neutral_ma": 12.0, "spray_flow_max_lpm": 5.0, "spray_pressure_min_margin_bar": 3.0, "proportional_gain_kp": 0.15, "integral_gain_ki": 0.008, "derivative_gain_kd": 0.02, "integral_limit_c": 5.0, "deadband_c": 0.3, "thermal_shock_rate_threshold_c_per_sec": 2.0, "rtd_fault_timeout_sec": 30, "valve_stuck_detection_timeout_sec": 5, "tube_wall_temp_margin_c": 30.0, "control_scan_interval_sec": 1.0, "data_history_seconds": 120.0 } ``` --- ## 📝 Implementation Checklist ### Hardware Validation - [ ] **Superheater outlet RTD** (Pt100 Class A, −50…+650°C range) - Installed in steam path (post-superheater) - Sealant/fitting rated for 540°C + 10 bar overpressure - Verified against boiler outlet saturation temperature - [ ] **Spray water proportional control valve** (4-20 mA solenoid) - Capacity: 0-5 L/min spray water at SH inlet pressure - Integral flow control (not blocked when power lost) - Tested: full open/close stroke + linearity check - [ ] **Spray water pump** (small centrifugal or gear pump) - Discharge pressure setpoint: SH inlet pressure + 3 bar - Relief valve setting verified - Suction: deaerator tank (≥0.5 bar) to prevent cavitation - [ ] **Spray water flow measurement** (turbine or electromagnetic meter) - 0-10 L/min range - Calibrated to ±2% - 4-20 mA output - [ ] **Spray water temperature measurement** (RTD) - Located at pump discharge (before entering superheater) - Typical 30-50°C from deaerator - [ ] **Spray pump pressure transmitter** - Range: 0-250 bar - Must monitor to ensure spray injection possible - [ ] **Reheater outlet RTD** (if applicable, separate attemperator) - Same class as SH outlet - Separate control valve (proportional) ### Commissioning (7-Day Procedure) **Day 1: Hardware Installation Verification** 1. Pressure test spray valve isolation block with 1.5× working pressure 2. Verify water flows through bypass (pump discharge relief) 3. Run pump 1 hour to inspect for leaks, noise 4. RTD response test: apply 50°C water, verify signal **Day 2: Low-Load Tuning (25-30% Capacity)** 1. Bring boiler to 25% load, manually position spray valve at 50% (12 mA) 2. Observe outlet temperature: record for 30 minutes (should stabilize) 3. Manually increase spray by 10% → observe temperature drop 4. Record response: ideal <5 seconds to steady state **Day 3: PID Gains (Conservative Start)** 1. Enable automatic control with minimal gains: - Kp = 0.05, Ki = 0.001, Kd = 0 2. Allow controller to trim once; observe settling 3. Increase Kp to 0.10 → test step response 4. Increase Ki to 0.002 → test offset removal over 1 minute **Day 4: Load Ramp Test (25% → 50% → 75%)** 1. At each load step, hold for 20 minutes 2. Record temperature, valve command, spray flow 3. Verify no excessive overshoot (>3°C) 4. Adjust Kd if response too slow (add 0.01 at a time) **Day 5: Full Load Test (80-95%)** 1. Ramp to 90% load in 10 minutes 2. Run 1 hour at constant load 3. Monitor for oscillation (±1°C peak-to-peak acceptable) 4. Record efficiency: should be optimal (lowest fuel cost) **Day 6: Reheater Commissioning** (if applicable) 1. Tune separate reheater attemperator same as superheater 2. Verify both loops independent + stable 3. Cross-check: reheater outlet should be <10°C below SH outlet **Day 7: Fault Scenario Testing** 1. Simulate spray water loss: shut pump discharge valve - Temperature should rise; alarm should trigger within 10 seconds - Operator should switch to manual valve adjustment 2. Simulate RTD failure: disconnect RTD - System should detect loss of signal; display fault - Allow manual mode takeover 3. Thermal shock test: ramp load 50% → 80% in 5 minutes - Monitor for temperature overshoot & undershoot - Verify no instability --- ## 📊 Expected Performance | Metric | Target | Achievable | Notes | |--------|--------|-----------|-------| | **Temperature accuracy** | ±3°C @ SP | ±1-2°C | Well-tuned PID | | **Response time** | <30 sec | 10-20 sec | Load step change | | **Overshoot** | <5°C | 1-3°C | Derivative damping | | **Settling time** | <2 minutes | 1-1.5 min | To within ±1°C | | **Spray valve response** | <2 sec | 1-1.5 sec | Solenoid + hydraulics | | **Tube metal margin** | >20°C below limit | 30-40°C typical | Safety factor | | **Oscillation** | ±1°C max | ±0.5-1°C | Deadband prevents chatter | --- ## 🔄 Advanced Variations ### Load-Based Feedforward If load changes predictably (ramp rate known): - Calculate expected temperature rise: ΔT = Load_Change × 0.25°C per % load - Pre-open spray valve 50 ms before load increase - Result: temperature stays within ±2°C during ramp (vs ±5°C without FF) ### Dual-Element Superheater If furnace has primary + secondary superheater banks: - Separate attemperator on secondary (cross-flow arrangement) - Primary heats to 480°C; secondary → outlet 540°C - Two cascaded loops: more stable response ### Evaporator Temperature Trim In combined cycle plants (boiler + GT): - If GT exhaust temperature rises (more gas available): - Automatically trim SH setpoint down 5°C - Reduce steam rate demanded; improve plant efficiency - Cascade: gas temp → steam temp FF ### Creep Rupture Protection (Long-Term) Monitor tube metal temperature trend: - If running consistently 15°C above nominal design: - Alert for inspection (creep damage accumulation) - Estimate remaining tube life: decreases exponentially with ΔT - Schedule replacement before rupture risk significant --- **Critical power plant steam temperature control — essential for boiler tube protection & plant efficiency.** > **MANDATORY**: Every power boiler with main superheater must implement spray water > attemperator per ASME PG-60. This template provides the baseline for SIL 2 temperature > control and creep rupture prevention.

More like this

Rate, comment, and get full access

Members can download files, rate contributions, and discuss fixes with the engineers who posted them — free.

Join the library