Field fix / guideDesign DocumentVendor-agnostic (IEC 61131-3)Generic Modulesindustrial-automation

Single Tank Level Control — Control Design

Shared by TSIMEREZIVO Team · 4 Oct 2026 · 37 views

# Generic Module: Single Tank Level Control **Version**: 1.0 **Complexity**: Low **Industries**: All (Water, Pharma, Food, Chemical, Oil & Gas) **PLC Languages**: Ladder, ST, FBD, SFC --- ## 📋 Overview Simple level control for a single tank with pump or valve control. The most fundamental control loop in industrial automation. **Use When:** - ✅ Single tank, single outlet (pump or valve) - ✅ Setpoint-based filling/draining - ✅ Simple hysteresis band operation - ✅ No cascade or advanced functions needed **Do NOT Use When:** - ❌ Two tanks (use Lead/Lag template) - ❌ Advanced control needed (use PID template) - ❌ Multiple outlet valves (use more complex logic) --- ## 🎯 Control Philosophy **Simple On/Off with Hysteresis** ``` IF Level < (Setpoint - Hysteresis) THEN Start Pump/Open Valve IF Level > (Setpoint + Hysteresis) THEN Stop Pump/Close Valve ``` **Example:** Setpoint 50%, Hysteresis ±5% - Start filling when level drops below 45% - Continue until level exceeds 55% - No restarts during this band (prevents chatter) **Typical Settings:** - Hysteresis: 2-5% of tank capacity - Pump delay: 1-2 seconds (debounce) - Sensor update: Every scan --- ## 🏗️ Control Logic (Pseudocode) ```pascal PROGRAM Tank_Level_Control VAR (* Settings *) Level_Setpoint : REAL := 50.0; (* % *) Level_Hysteresis : REAL := 4.0; (* ± % *) Pump_Delay : INT := 10; (* 100ms ticks *) Pump_Delay_Counter : INT := 0; (* Inputs *) Level_Sensor : REAL; (* 0-100 % from analog input *) (* Outputs *) Pump_Command : BOOL := FALSE; (* Status *) Pump_Running : BOOL := FALSE; Tank_Empty : BOOL := FALSE; Tank_Full : BOOL := FALSE; END_VAR (* Read sensor *) Level_Sensor := READ_ANALOG_INPUT(AI_TANK_LEVEL); (* Detect boundary conditions *) Tank_Empty := Level_Sensor < 10.0; (* 10% = empty *) Tank_Full := Level_Sensor > 95.0; (* 95% = full *) (* Pump control logic *) IF NOT Tank_Empty THEN (* Low level: start pump *) IF Level_Sensor < (Level_Setpoint - Level_Hysteresis) THEN Pump_Delay_Counter := Pump_Delay_Counter + 1; IF Pump_Delay_Counter >= Pump_Delay THEN Pump_Command := TRUE; Pump_Delay_Counter := 0; END_IF; (* High level: stop pump *) ELSIF Level_Sensor > (Level_Setpoint + Level_Hysteresis) THEN Pump_Command := FALSE; Pump_Delay_Counter := 0; (* In hysteresis band: maintain state *) ELSE (* Do nothing *) END_IF; ELSE Pump_Command := FALSE; END_IF; (* Safety: prevent overfill *) IF Tank_Full THEN Pump_Command := FALSE; END_IF; (* Write output *) WRITE_DIGITAL_OUTPUT(DO_PUMP_CMD, Pump_Command); Pump_Running := Pump_Command; END_PROGRAM ``` --- ## 🏷️ Tag List | Tag | Type | I/O | Description | Range | Update | |-----|------|-----|-------------|-------|--------| | `TANK_01_LEVEL` | REAL | Input | Tank level measurement | 0-100 % | Continuous | | `TANK_01_LEVEL_SP` | REAL | Param | Level setpoint | 0-100 % | Manual | | `TANK_01_LEVEL_HB` | REAL | Param | Hysteresis band | 0-10 % | Manual | | `TANK_01_PUMP_CMD` | BOOL | Output | Pump run command | - | Continuous | | `TANK_01_PUMP_RUN` | BOOL | Status | Pump running status | - | Continuous | | `TANK_01_EMPTY` | BOOL | Alarm | Level < 10% | - | Continuous | | `TANK_01_FULL` | BOOL | Alarm | Level > 95% | - | Continuous | | `TANK_01_LOW` | BOOL | Alarm | Level < setpoint - HB | - | Continuous | | `TANK_01_HIGH` | BOOL | Alarm | Level > setpoint + HB | - | Continuous | --- ## 🚨 Alarm & Trip Matrix | Alarm | Condition | Severity | Action | Auto-Reset | |-------|-----------|----------|--------|-----------| | **Tank Low** | `TANK_01_LEVEL < SP - HB` | Warning | Alert operator, log | Yes (when filled) | | **Tank High** | `TANK_01_LEVEL > SP + HB` | Warning | Alert operator, log | Yes (when drained) | | **Tank Empty** | `TANK_01_LEVEL < 10%` | Critical | Stop pump, raise alarm | Manual | | **Tank Full** | `TANK_01_LEVEL > 95%` | Critical | Stop pump, raise alarm | Manual | | **No Level Change** | `Level unchanged for 5 min` | Critical | Pump failed? | Manual check | | **Sensor Failure** | `Level = 0 AND pump_on = TRUE` | Critical | Stop pump, check sensor | Manual | --- ## 📺 HMI Layout ``` ┌─────────────────────────────────────┐ │ TANK 01 - LEVEL CONTROL │ ├─────────────────────────────────────┤ │ │ │ Level: 62.5% [████████░░░░] │ │ │ │ Setpoint: 50% ±4% │ │ │ │ Pump Status: [RUNNING] (✓ green)│ │ │ │ ┌─────────────────────────────┐ │ │ │ Mode: [AUTO] [MANUAL] │ │ │ └─────────────────────────────┘ │ │ │ │ ┌─────────────────────────────┐ │ │ │ Manual Control: │ │ │ │ [START] [STOP] [RESET] │ │ │ └─────────────────────────────┘ │ │ │ │ Alarms: [✓ None] [Log] [Clear] │ │ │ └─────────────────────────────────────┘ ``` **Display Elements:** - Real-time level bar (visual feedback) - Numeric level value - Setpoint + hysteresis band shown - Pump status (Running = green, Stopped = gray, Fault = red) - Manual override buttons (only in maintenance mode) - Alarm status with ack/clear buttons - Last updated timestamp --- ## 🔧 Configuration Parameters All settings should be accessible without recompiling: ```json { "tank_id": "TANK_01", "level_setpoint_percent": 50.0, "level_hysteresis_percent": 4.0, "pump_start_delay_ms": 1000, "pump_stop_delay_ms": 500, "empty_threshold_percent": 10.0, "full_threshold_percent": 95.0, "no_change_timeout_minutes": 5, "sensor_range_min": 0, "sensor_range_max": 100, "pump_type": "centrifugal", "valve_type": "solenoid", "control_device": "pump" } ``` --- ## 📝 Implementation Checklist ### Before Deployment - [ ] **Hardware verified** - [ ] Level sensor calibrated (0% = empty, 100% = full) - [ ] Pump/valve responds to command - [ ] All wiring checked - [ ] **Parameters configured** - [ ] Setpoint appropriate for application - [ ] Hysteresis set (typical: 3-5%) - [ ] Thresholds (empty, full) match tank - [ ] **Safety verified** - [ ] Overfill protection working (pump stops at 95%) - [ ] Underfi ll protection working - [ ] Manual override tested - [ ] **Alarms tested** - [ ] Low level alarm triggers at correct threshold - [ ] High level alarm triggers at correct threshold - [ ] Alarms can be acknowledged & cleared - [ ] **Telemetry enabled** - [ ] Level value transmission to SCADA - [ ] Pump status transmission - [ ] Alarm events logged ### During Commissioning 1. **Static test** (pump off): - Set level to 30% → verify pump command sent - Set level to 70% → verify pump command stops 2. **Dynamic test** (pump running): - Start filling → monitor level rise smoothness - Verify pump shuts off at setpoint + hysteresis - Verify pump restarts at setpoint - hysteresis - Run for 10 cycles without chatter 3. **Edge cases**: - Tank at 5% → verify empty alarm, pump doesn't start - Tank at 98% → verify full alarm, pump stops immediately - Simulate sensor failure → verify operator alert --- ## 📊 Typical Performance With proper configuration: - **Response time**: 1-2 seconds from setpoint breach to pump command - **Oscillation**: ±2% around setpoint (within hysteresis) - **Stability**: No hunting/chatter when in band - **Reliability**: >99.9% uptime (simple logic, no PID tuning needed) --- ## 🔄 Variations ### Dual Pump (Duty/Standby) Add second pump tag `TANK_01_PUMP_02_CMD` and alternate every 24h automatically. ### Flow Control (Valve) Replace `PUMP_CMD` with `VALVE_POSITION` (0-100% opening). ### PID Control (Advanced) For better precision, use **Temperature Control (PID)** template and adapt for level. ### Multi-Tank Use the **Pump Control (Lead/Lag)** template instead. --- ## ✅ Checklist for Template Completeness - ✅ Control logic clear and simple - ✅ No external dependencies - ✅ Alarms well-defined - ✅ HMI layout provided - ✅ Configuration parameterized - ✅ Implementation steps documented - ✅ Edge cases identified - ✅ Failure scenarios tested --- **Template ready for production deployment.**

More like this

Rate, comment, and get full access

Members can download files, rate contributions, and discuss fixes with the engineers who posted them — free.

Join the library