Field fix / guideDesign DocumentVendor-agnostic (IEC 61131-3)Power Plantindustrial-automation

Turbine Governor Control — Control Design

Shared by TSIMEREZIVO Team · 4 Oct 2026 · 95 views

# Power Generation Template: Turbine Governor Control ## 1. Overview **Purpose:** Speed and load control of a steam or gas turbine via the electro-hydraulic governor. Covers isochronous speed control (islanding), droop control (grid-connected), acceleration limiting, overspeed protection, and valve position control. **Industry Standards:** - IEEE 421.5 (Recommended Practice for Excitation System Models for Power Stability Studies) - IEEE 1110 (Guide for Synchronous Generator Modeling Practices) - IEC 60034-3 (Rotating Electrical Machines — Specific Requirements for Turbogenerators) - IEC 60050-411 (Steam Turbines — Terminology) - NERC PRC-024 (Generator Frequency and Voltage Protection Settings) - API 612 (Special Purpose Steam Turbines for Petroleum, Chemical, and Gas Industry Services) **Critical Constraints:** - **Overspeed trip:** 110% rated speed — hardware trip (spring-loaded), NOT software only (IEC 61508 SIL-2) - **Critical speed avoidance:** Do NOT hold speed in ±3% of critical speed bands (rotor resonance) - **Acceleration limit:** Maximum 100 rpm/s during startup (thermal stress on rotor) - **Valve stroking rate:** Maximum 15%/s on steam control valve (prevents steam hammer) - **Governor deadband:** ±0.06 Hz (IEEE definition for primary frequency response) - **Droop setting:** 4–5% (standard NERC/UCTE grid code); 0% = isochronous - **Lubrication interlock:** Governor system MUST be disabled if lube oil pressure < 0.8 bar - **Bearing temperature:** Trip at 100°C (journal) / 95°C (thrust); alarm at 90°C / 85°C **Relevant Physics:** - Governor droop: **Δf/f_rated = −R × ΔP/P_rated** where R = droop coefficient (0.04 = 4%) - Synchronizing torque: **T_sync = (V₁V₂/X_s) × sin(δ)** — power angle stability limit - Steam flow / power: **P_mech = ṁ_steam × (h_inlet − h_exhaust) × η_turbine** - Turbine time constant: **T_turbine = J_rotor × ω_rated / P_rated** (inertia constant H ≈ 4–8 s) - Centrifugal stress: **σ_c = ρ × ω² × r² / 2** — limits maximum overspeed margin --- ## 2. Control Philosophy **Challenge:** A turbine governor must serve two mutually exclusive objectives: maintain constant frequency (isochronous for islanding) OR share load proportionally with other generators (droop for grid parallel). Switching between modes without a bumpless transfer causes power surges. **Solution: Bumpless Dual-Mode Governor with Droop/Isochronous Switching** ``` Mode 1: ISOCHRONOUS (Island / Off-Grid) SP: 50.00 Hz (or 60.00 Hz — region dependent) PV: Turbine speed (from magnetic pickup or proximity probe) Output: Steam/fuel control valve position 0–100% Algorithm: PID speed controller Kp = 12.0, Ki = 4.0, Kd = 0.8 Deadband: ±0.02 Hz (prevent hunting) Mode 2: DROOP (Grid-Connected) Droop: 4% (Δspeed/Δload) Reference point: Current load at moment of connection Output: Valve position = baseline_valve + droop_correction Droop correction: ΔV = -(f_actual - f_grid) / (R × f_rated) × P_rated / ΔP_max No integral action in droop mode (grid acts as integrator) Startup Sequencing: 1. Rotor turning gear (0–50 rpm) 2. Slow roll and inspection (50–200 rpm, hold 15 min for thermal soak) 3. Critical speed transit (ramp through critical band at max 50 rpm/s) 4. Acceleration to rated (200→3000 rpm at ≤100 rpm/s) 5. Speed hold at 3000 rpm — synchronize with grid 6. Close breaker and transfer to droop control Protection Hierarchy (hardware >> software): 1. Mechanical overspeed bolt (110% — physical) 2. Electronic overspeed relay (109% — hardwired trip relay) 3. Software overspeed alarm (107% — SCADA alert) 4. Governor speed limit (105% — software clamp) ``` --- ## 3. Control Logic ```pascal { === TURBINE GOVERNOR CONTROL === } { Dual-mode: Isochronous (island) and Droop (grid-parallel) } PROGRAM Turbine_Governor CONSTANTS RATED_SPEED_RPM = 3000.0 { rpm — 50 Hz, 2-pole generator } RATED_FREQ_HZ = 50.0 { Hz } RATED_POWER_KW = 15000.0 { kW — generator nameplate } DROOP_PCT = 4.0 { % — standard grid droop } DEADBAND_HZ = 0.02 { Hz — governor deadband } TRIP_SPEED_PCT = 109.0 { % rated — electronic overspeed trip } ALARM_SPEED_PCT = 107.0 { % rated — overspeed alarm } CRIT_SPEED_LOW = 1400.0 { rpm — critical speed band low } CRIT_SPEED_HIGH = 1700.0 { rpm — critical speed band high } CRIT_XSPEED_LOW = 2100.0 { rpm — second critical speed band } CRIT_XSPEED_HIGH = 2300.0 { rpm — second critical speed band } ACCEL_LIMIT_RPMS = 100.0 { rpm/s — max acceleration } VALVE_RATE_LIMIT = 15.0 { %/s — max valve stroke rate } LUBE_OIL_MIN_BAR = 0.8 { bar — governor lube interlock } BRG_TEMP_ALARM_C = 90.0 { °C — journal bearing temperature alarm } BRG_TEMP_TRIP_C = 100.0 { °C — journal bearing temperature trip } KP_ISO = 12.0 { Isochronous Kp } KI_ISO = 4.0 { Isochronous Ki } KD_ISO = 0.8 { Isochronous Kd } VARIABLES { Inputs } speed_rpm : REAL { rpm — magnetic pickup / tachometer } generator_freq_hz : REAL { Hz — frequency transducer } grid_freq_hz : REAL { Hz — grid frequency measurement } generator_kw : REAL { kW — power transducer } lube_oil_press_bar : REAL { bar — lube oil header pressure } brg1_temp_c : REAL { °C — bearing 1 temperature } brg2_temp_c : REAL { °C — bearing 2 temperature } thrust_temp_c : REAL { °C — thrust bearing temperature } steam_press_bar_g : REAL { bar g — inlet steam pressure } breaker_closed : BOOL { Generator circuit breaker status } { Outputs } ctrl_valve_cmd : REAL { % — steam/fuel control valve } trip_signal : BOOL { TRUE = trip turbine } governor_ready : BOOL { TRUE = healthy, no inhibits } alarm_overspeed : BOOL alarm_bearing_temp : BOOL alarm_lube_low : BOOL alarm_crit_speed : BOOL { Internals } governor_mode : INT { 0=OFF 1=ISOCHRONOUS 2=DROOP } speed_error_hz : REAL { Hz — frequency error } speed_integral : REAL { Integral accumulator } speed_derivative : REAL { Derivative term } prev_speed_error : REAL { For derivative calculation } valve_cmd_raw : REAL { % — unsaturated valve command } valve_cmd_last : REAL { % — previous cycle (rate limiting) } droop_baseline_kw : REAL { kW — load at mode switch } droop_baseline_pct : REAL { % valve — valve at mode switch } trip_pending : BOOL { Latch for trip condition } speed_pct : REAL { % rated speed } freq_hz : REAL { Derived from speed_rpm } CONST MODE_OFF = 0 MODE_ISOCHRONOUS = 1 MODE_DROOP = 2 BEGIN { --- Derived Measurements --- } freq_hz := speed_rpm / 60.0 speed_pct := speed_rpm / RATED_SPEED_RPM * 100.0 { --- Hardware Trip Conditions (unconditional) --- } trip_pending := speed_pct >= TRIP_SPEED_PCT OR lube_oil_press_bar < LUBE_OIL_MIN_BAR OR brg1_temp_c >= BRG_TEMP_TRIP_C OR brg2_temp_c >= BRG_TEMP_TRIP_C OR thrust_temp_c >= 95.0 IF trip_pending THEN ctrl_valve_cmd := 0.0 trip_signal := TRUE governor_mode := MODE_OFF { Latch — requires manual reset after inspection } RETURN END_IF trip_signal := FALSE governor_ready := lube_oil_press_bar >= LUBE_OIL_MIN_BAR { --- Alarms --- } alarm_overspeed := speed_pct >= ALARM_SPEED_PCT alarm_bearing_temp := brg1_temp_c >= BRG_TEMP_ALARM_C OR brg2_temp_c >= BRG_TEMP_ALARM_C OR thrust_temp_c >= 85.0 alarm_lube_low := lube_oil_press_bar < LUBE_OIL_MIN_BAR + 0.2 alarm_crit_speed := (speed_rpm >= CRIT_SPEED_LOW AND speed_rpm <= CRIT_SPEED_HIGH) OR (speed_rpm >= CRIT_XSPEED_LOW AND speed_rpm <= CRIT_XSPEED_HIGH) { --- Governor Mode Control --- } CASE governor_mode OF MODE_ISOCHRONOUS: { Frequency error with deadband } speed_error_hz := RATED_FREQ_HZ - freq_hz IF ABS(speed_error_hz) < DEADBAND_HZ THEN speed_error_hz := 0.0 END_IF { PID calculation } speed_integral := speed_integral + speed_error_hz * SCAN_TIME_S speed_derivative := (speed_error_hz - prev_speed_error) / SCAN_TIME_S prev_speed_error := speed_error_hz { Anti-windup: freeze integral at valve saturation } IF valve_cmd_raw >= 100.0 AND speed_error_hz > 0.0 THEN speed_integral := speed_integral - speed_error_hz * SCAN_TIME_S END_IF IF valve_cmd_raw <= 0.0 AND speed_error_hz < 0.0 THEN speed_integral := speed_integral - speed_error_hz * SCAN_TIME_S END_IF valve_cmd_raw := KP_ISO * speed_error_hz + KI_ISO * speed_integral + KD_ISO * speed_derivative MODE_DROOP: { Droop: proportional load sharing — no integral (grid holds frequency) } { ΔValve = -Δf / (droop × rated_freq) × valve_at_rated_load } valve_cmd_raw := droop_baseline_pct - (freq_hz - RATED_FREQ_HZ) / (DROOP_PCT / 100.0 * RATED_FREQ_HZ) * (droop_baseline_pct / 100.0) * 100.0 MODE_OFF: valve_cmd_raw := 0.0 speed_integral := 0.0 END_CASE { --- Valve Output Clamping and Rate Limiting --- } valve_cmd_raw := MAX(0.0, MIN(100.0, valve_cmd_raw)) { Stroke rate limit: ±15%/s } IF valve_cmd_raw - valve_cmd_last > VALVE_RATE_LIMIT * SCAN_TIME_S THEN ctrl_valve_cmd := valve_cmd_last + VALVE_RATE_LIMIT * SCAN_TIME_S ELSIF valve_cmd_last - valve_cmd_raw > VALVE_RATE_LIMIT * SCAN_TIME_S THEN ctrl_valve_cmd := valve_cmd_last - VALVE_RATE_LIMIT * SCAN_TIME_S ELSE ctrl_valve_cmd := valve_cmd_raw END_IF valve_cmd_last := ctrl_valve_cmd { --- Mode Switch: Isochronous → Droop (bumpless transfer) --- } { Call when breaker closes: record current valve position and load } { droop_baseline_pct := ctrl_valve_cmd } { droop_baseline_kw := generator_kw } { governor_mode := MODE_DROOP } { Reset integral accumulator to avoid bump: speed_integral := ctrl_valve_cmd / KI_ISO } END_PROGRAM ``` --- ## 4. Tag List (ISA-5.1 Naming) | Tag Name | Description | Type | Direction | EGU | Lo | Hi | |---|---|---|---|---|---|---| | `GT01_SPEED_PV` | Turbine speed | REAL | Input | rpm | 0 | 3600 | | `GT01_FREQ_PV` | Generator frequency | REAL | Input | Hz | 45 | 55 | | `GT01_GRID_FREQ_PV` | Grid frequency reference | REAL | Input | Hz | 49 | 51 | | `GT01_GEN_KW_PV` | Generator active power | REAL | Input | kW | 0 | 16000 | | `GT01_LUBE_PRESS_PV` | Lube oil header pressure | REAL | Input | bar | 0 | 4 | | `GT01_BRG1_TEMP_PV` | Bearing 1 temperature | REAL | Input | °C | 20 | 110 | | `GT01_BRG2_TEMP_PV` | Bearing 2 temperature | REAL | Input | °C | 20 | 110 | | `GT01_THRUST_TEMP_PV` | Thrust bearing temperature | REAL | Input | °C | 20 | 100 | | `GT01_STEAM_PRESS_PV` | Inlet steam pressure | REAL | Input | bar g | 0 | 60 | | `GT01_BKR_STATUS` | Generator breaker closed | BOOL | Input | — | — | — | | `GT01_CTRL_VLV_CV` | Steam control valve position | REAL | Output | % | 0 | 100 | | `GT01_TRIP_CMD` | Turbine trip signal | BOOL | Output | — | — | — | | `GT01_GOV_MODE` | Governor mode (0/1/2) | INT | Internal | — | — | — | | `GT01_GOV_READY` | Governor healthy status | BOOL | Internal | — | — | — | --- ## 5. Alarm Configuration (ISA-18.2) | Alarm Tag | Description | Priority | Setpoint | Action | |---|---|---|---|---| | `GT01_OS_ALARM` | Overspeed alarm | Critical | 107% rated | Alert operator; verify mechanical trip | | `GT01_OS_TRIP` | Overspeed electronic trip | SIL-2 | 109% rated | Immediate trip — no delay | | `GT01_LUBE_ALARM` | Lube oil pressure low | Critical | <1.0 bar | Alert; inhibit start; trip if running | | `GT01_BRG_TEMP_ALM` | Bearing temperature high | High | 90°C | Reduce load; inspect at next stop | | `GT01_BRG_TEMP_TRIP` | Bearing temperature trip | Critical | 100°C | Emergency shutdown | | `GT01_CRIT_SPD_ALM` | Operation in critical speed band | High | 1400–1700 rpm | Accelerate through; alert | | `GT01_FREQ_DEV_ALM` | Grid frequency deviation | Medium | ±0.5 Hz | ABAC response; investigate grid | --- ## 6. Commissioning Checklist - [ ] Mechanical overspeed bolt: Set to 110% rated speed; test annually per manufacturer procedure - [ ] Electronic overspeed relay: Calibrated to 109% using speed signal injection; test on each outage - [ ] Verify governor deadband: Step ±0.02 Hz; confirm no valve response within deadband - [ ] Stroke test control valve: 0% → 100% → 0%; record stroke time; verify rate limit operation - [ ] Critical speed transit test: Ramp through 1400–1700 rpm range; confirm transit < 120 s - [ ] Isochronous mode test (islanding): Trip grid breaker; confirm frequency holds 50 Hz ±0.1 Hz - [ ] Droop test: Apply load step 10% rated; confirm governor response and droop characteristic - [ ] Bumpless transfer test: Switch isochronous→droop; confirm MW output variation < 2% - [ ] Lube oil interlock: Reduce lube pressure to 0.6 bar; confirm governor inhibit - [ ] Bearing temperature trip: Inject simulated signal at 100°C; confirm trip and valve closure

More like this

Rate, comment, and get full access

Members can download files, rate contributions, and discuss fixes with the engineers who posted them — free.

Join the library